ALW680RAC (PALW680RAC) Amana Washer - Instructions

I tipped the tub towards the area where the springs were and connected them. They broke because that particulary area seemed to get moisture and they rusted. Truthfully, although the machine still works, its last days are just down the road.

It was so simple I don't think I even need to explain. Couple of screws in and out and done. Saved big money by doing the repair myself...I was surprised how quickly the part arrived. I was able to access from the back of my machine. Did not have to remove the top. Very easy thanks

took the belt out and took the thing out and fixed then put it back.

Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.

Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.

No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.

I unplug the power plug, turned off water supply and unsrewed the water lines connected to the clogged valve.I unsrewed six screws on the front of the washing machine and took the front panals off. lifted the the washing top and replace the hose and intake valve, which was shipped to me. put the top down and put the two front panals. reconnected the water supply to the new valve and turned the water back on. connected the electric plug.works as good as new.

First removed all screws with a nutdriver then lifted the body from the base. Removed the two hoses at the pump (be ready for excess water). Removed the 9/16 bolts (4) to drop the motor assy. I also took off the two front balance springs to have easy access. I at this point was able to remove the pulley and put new belt & pump on the motor. Remember to watch carefully to align belt. removing the idler pulley is a no brainer. Took about 45mins. to complete, a no pro job!!

I removed three screws to gain access to the timer. It has a label which describes how to remove the contol knob but does not address the removal of the timer knob skirt. I tried prying it off but was unsuccessful. This caused the removal of the timer to be very difficult. After the skirt came off the timer was easy to remove. The timer is held in place by one screw. The new timer went in real easily.

Unplugged washer from power source. Dissconnect the water supply. Take off lower panel. Undo big spring. Remove 4 bolts that hold the motor. Unplug the motor. remove motor and belt. While on the bench I regreased the Idler pulley. then reverse the procedure to reassemble

I disconnected the water supply line to washer and moved washer into open area. I removed the front panel of washer to gain access to drain hose. I removed hose and reinstalled new hose. I did turn the hose holder inside the washer as it allowed the old hose to rub against the housing support of the washer causing the hose to leak. I was glad that I read the article that someone mentioned in their repair. The new hose was somewhat difficult to maneuver through the back of the washer and through the part that held the hose; otherwise, it was rather easy. Thanks for the feed back on your web page.

1. unplug unit 2. remove front access plate 3. disconnect tension spring on drive belt 4. remove 4 motor mount screws 5. disconnect intake and return lines from pump using a pliers to decompress compression rings and sliding lines off. 6. Manipulate motor and loosen drive belt from bottom of tub and let it hang. 7. tilt motor bottom out exposing pump and remove 3 screws using TREX head driver and remove pump. 8. install new pump

Part received was correct (5 days ARO). Removed motor assy from unit (left wires connected). Found drive belt was also worn out & obtained a new one locally. Seperated old pump from rusted motor shaft using 2 screwdrivers. Had to use a file to lightly "polish" rust off motor shaft to install new pump. On-line parts diagram helpful in getting belt properly alinged to idler pully. Machine now runs smoothly, dosn't leak and sound like new. Wife happy (me too)!

Laid washer on its side and had to remove the motor,replaced the pulley and belt replaced the motor and put all parts back together washer spins and runs like it did when it was new.we did not need the screw or nut but did not know when ordering parts

I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.

Remove the front of the washer. Remove the pump and motor assembly using the 1/2 inch socket. Remove the pump from the motor and hoses from the pump. Replace the bad idler pulley and place new belt on pulley. Reassemble the pump to the motor and install the assembly back into the washing machine. Reasemble the hoses and put belt on driven pulley for the drum. Reinstall the front cover.

I first ordered the parts and to my dismay, I ordered the wrong belt for the spin belt. I called customer service in which received an Return Merchandise Number and ordered the correct belt. PartSelect was prompt on sending the correct out by FedEx, thank you for an excellent experience.