ALW5 Amana Washer - Instructions

First I unscrewed the bottom of the front panel.
Then I realized the front panel pulls off from the top.
(manuals are helpful only if read!) I took the tub hose off at the tub and used my wet vac to remove all the excess water. (no towel needed) Using the appropriate size torx head bit, an extension and a small socket wrench to ... Read more undo the screws holding the pump. I had to push and pull the bottom of the tub slightly to get proper room for the small socket wrench. pull the pump down and off. take the hoses off and place them on the new pump. reverse the process. tighten the clamps and replace the front cover.

Followed instructions that came with parts. Still making a noise not as loud as before, must be transmission bearing.

Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.

replaced belt that was wore out. decided to replace pump while I had washer apart.

I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remov ... Read more e the part but putting the new agitator on was simple.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

Since the agitator and bell housing seperated as once piece from the drive shaft I didn't have to remove them and the schematic showed how the agitator snapped on to the bell housing and the parts I needed for the fix. The new seal went on with no problem, I just used some of the supplied grease on the tight spots. The hardest part w ... Read more as attaching the bell housing. It came to within an inch of the top of the shaft with no problem with a rubber hammer. But the top screw shroud broke when I tried to hammer it the rest of the way using a wood dowel and a block of wood. I couldn't even get the threads of the supplied screw to even touch the drive shaft. So I bought a longer (1 inch) cap screw from the hardware store and added a washer and suplied ring. After torqing it to 5 ft-lbs instead of the 10-20 the plastic beneath the screw was looking kind of thin and stressed and I was afraid of it breaking through or the screw snapping off in the shaft, so I left it alone and used some silicone caulk to seal in the plug that goes in on top of the screw since the side of the shroud broke off. I slipped on the agitator and am testing a load now as we speak. If I get ten more years out of the washer it will definitely be worth the $100 in parts and shipping !

a nail from my pocket fell out and was in one of the holes in the in the tub and bound up the tub.when it wold try to spin.ordered the belt and had to order a pump also it melted the bearing in it

My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.

With the right tools this job, should not be that complicated, to me the hardest part was finding the right tools, 1/4 inch small rachet ( the smallest the better,) with a 2 inch extension and a Torx head socket, also known as a 6 lobe,(T25 thats the # that is on the socket) also you need a flat head screw driver,or a 1/4 socket to ... Read more take the cover off.. and of course the right belt, you might also need a flash light, watch out for spiders, specially black widows, i found a few, First you take the cover off, it should be the easiest part, then, put the rachet,( the smallest the better) with the 2 inch extension and the socket, to take out the water pump, it should be white, it should be only three screws, take your time, when taking out the screws hold them so they don't fall, in to the whasher, it happened to me and it took me a long time to find one of the screws, once you take the 3 screws move the water pump aside it should just drop down from the shaft that drives it, it is not necessary to take the hoses off the pump, put the new belt in place, make sure place it trough the tensioner, there is a guide in the AMANA web site when if you are not so sure, on how the belt goes, once you place the belt, put the water pump back, put the three screws back, put the cover back, run the machine trough a new cycle, Reason why is because i try to run it trough the spin cycle only after i put it together and the belt wouldn't spin, only the motor,Don't forget to unplug the power from the wall before staring all this, I hope this was of some help to you,

I opened the bottom and found the belt had broke in half. i ordered a new belt from Maytag online and found a you tube video that showed exactle how to change it. the only thing i had to do afterwards was tighten the tensioner.eazy pezy!

I read instructions on how to change the pump. I unplugged the washer and then I took off the front panel.I removed the hose clamps and removed the two hoses from the pump.Then I removed the two front springs that hold the drum in place. Be careful because these springs are under tension. I removed the 4 bolts that held the motor to the ... Read more tub. I unplugged the wires leading to the motor. I removed the motor. I turned the motor upside down and removed the pump and belt. I ordered a belt along with the pump because it was worn. It is best to note how the belt is installed. I took a picture before removing the pump from the motor for future reference if needed. Installation of the new pump and belt was not difficult. I worked the belt around the drum pulley and made sure it turned freely. After completing installation I ran the washer through a short cycle to check for leaks before installing the front cover.

Fixed the problem easy to do just take your time putting in bearing in plastic tub