If your clothes washer is leaking, it is likely that there could be an issue with one of the hoses. If the hoses are in working order, you should check the washers connecting the hose to your unit. Rubber washers are tasked with enhancing the seal between the hose and washer. A faulty or damaged washer will not be able to perform this pro...Read moreperly, and water will be able to leak from the poor connection. This OEM part is sold individually, so make sure you order the quantity that is needed. The washer measures 1 1/16 inches x 5/8 inches.
This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to ...Read morewear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.
This control knob is a little over an inch in diameter. It is beige in color and is made of plastic. This knob has a blue indicator line, and will accept a 'D' shaped shaft.
The compressor relay and overload kit is an assembly for your refrigerator. The function of the overload is to protect the compressor from overheating by being mounted to the side of the compressor. The purpose of the relay is to boost the compressor. This assembly comes with two smaller plastic pieces that are less than two inches by one...Read more inch. One is black and the other is white. The kit also comes with a red wire tubing. The most common reason for needing to replace the overload and relay is if your fridge is too warm or will not start.
Start relay and overload for production compressor only. The start relay boosts the compressor, and then shuts off as soon as the motor gets up to speed. The overlay provides added protection against excessive current and against excessive temperature use.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator stop working
23 of 33 peoplefound this instruction helpful.
SAL from UPLAND, CA
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
First I removed the relay and over load and exam. Saw that the relay was burnt. Before I order the part I check to see if the compressor was still working by jumping the common start and run terminals.It did. I also checked the start capacitor with a capacitor tester it was good. I than order the part which came the very next day.Installe
... Read mored the part
Read less
Was this helpful?
Thank you for voting!
My A/C unit quit working on the hottest day of the year! I had this A/C unit for 13 years and I just knew I'd never find a fan blade for the same make and model, so I tried to go purchase a new one but couldn't find one big enough since it was so late in the season.
16 of 21 peoplefound this instruction helpful.
Tracy from Morgantown, WV
Really Easy
15 - 30 mins
Screw drivers
After receiving the fan blade, I popped off the old one and put on the new one! The A/C unit worked like new once again!! It even blew colder air than before! The hardest part about the entire process was getting the13 year old fan blade off! I'd recommend your website to anyone looking for a part! Thank you for all your help!!
Was this helpful?
Thank you for voting!
old fan motor made horrible screeching sound and siezed up
5 of 6 peoplefound this instruction helpful.
Dave from Roswell, GA
Easy
Less than 15 mins
Nutdriver
Removed 4 hex head screws around base of metal housing and 2 screws on bottom front holding on plastic grating and one screw holding housing to switch plate at top front. Hinged grating on back just pops off. Removed two screws holding fan motor on. Unclipped wire terminals (2). Bolted new fan in place.
One hitch was that o
... Read morene of the little terminal connectors that came with this fan motor was too small, so I had to buy some the right size, and strip the wire and crimp one of those on.
Also, this fan motor is two-speed, and my old dehumidifier is one-speed, so, according to the very helpful instructions, I just taped off one of the wires (not the one I would have guessed--it has you replacing the red with the black and taping off the new red one).
Then reassembled in reverse order, of course.
The only other thing is just that this stinkin' thing was so expensive, but it works fine. It's been humming away for days now, and my basement is once again in the pocket, about 50 - 55% humidity.