AGS76 Amana Range - Instructions

I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and pla ... Read more ced them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I removed the screws(4) that held the old glass in place, cleaned the broken glass chips from the frame and carefully reassembled the door.

removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine

Removed old igniter and replaced with new one.Tested oven and it went on. You need a phillips screwdriver to remove two screws and a small socket for the third screw to remove the igniter cage. Then pull out the wires from under the oven and disconnect. Reverse procedure to install new igniter. Reuse original connectors. Be very careful ... Read more with the igniter because the tip is very fragile and can break easily.

The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.

Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.

Using a meter, we determined each of the four igniters had continuity from end to end and also had continuity from the end of each igniter back to the spark module. At that point we decided the module was probably bad and, after reviewing some similar-sounding problems on this website, I ordered the module. Installation was simple and s ... Read more olved the problem. All four burners now ignite as they should. One caution - the installation instructions that came with the new module did not describe anything like my stove.

Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!

We unplugged the stove and turned off the gas. We slid the oven door off just to make it easier. Unscrewed 3 screws holding the igniter in place. Pulled the igniter out from the back of the stove. Disconnected the two wires. Slid the new igniter in the holder. Rewired it and slid it back into place. Put the screws back in and it wa ... Read more s done. Plugged it back in, turned the gas on, tried it out and presto! It was perfect! Lit immediately and strong and now i have a brand new 20 year old stove. lol Happy girl! And this was done by 2 50 year old women!

Removed the burners 2 screws per burner disconnected the wires to the burners. Lifted the oven top off removed original ignition module. Installed wires to the new module taking note of replacement location. Than mounted new ignition module. Tha only hiccup was dropping 1 screw down into the stove lining found replacement screw and instal ... Read more led module. Cleaned and replaced top. Mounted burners and the stove is working like new. Project proved to be quite simple and guick. Thanks to partselect for there prompt delivery and other peoples input on install made it quite easy and simple,