The splash guard, also known as a mounting gasket, is used for garbage disposals. The guard creates a tight seal between the sink and the garbage disposal ring. This part is black in color and made of rubber. It covers the top of the sink drain and it opens in the center to allow water and food particles into garbage disposal. It does thi...Read mores while ensuring liquids and food do not splash back into the sink. This should be a solution to your issue of garbage coming back out of the sink. Refer to the instructional diagram provided by the manufacturer for installation instructions.
This capacitor (Refrigerator and Freezer Compressor Run Capacitor, Run Capacitor) provides the voltage or energy current required to start the compressor and keep it running. It allows the compressor in your appliance to easily cycle on and off. This capacitor mounts directly onto the compressor starting relay. If the capacitor is faulty ...Read morethe compressor may get unusually hot and draw excessive amperage. It the compressor overheats, it may fail to run until it cools down again. The compressor may also get noisy from overheating. If this part is totally electrically open, it is defective (often due to overheating) and needs to be replaced. The part measures 1 inch by 1-1/2 inches, and is constructed of plastic with two metal wire terminals. This item includes 1 capacitor, sold individually. This part comes in black.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
The sink flange attaches to your sink drain opening and provides a connection to mount the disposal unit to the sink itself. If your food waste disposer is leaking, there are a few places that you should inspect. If the leak appears to be coming from around the connection to the sink, look carefully at the sink flange, as there could be a...Read moren issue with the flange itself, or its gaskets. Remember to disconnect the power from your food waste disposal unit before beginning this repair. This OEM replacement part has an outer diameter of approximately 4.5 inches, and an inner diameter of approximately 3 inches.
This item is sold individually. The fiber sink flange gasket works with your food waste disposer. This part creates a seal that prevents any water from leaking. It is positioned between the sink flange and the disposal mounting ring. The flange may break apart over time and cause leaking and will need to be replaced. The flange gasket is ...Read moredonut shaped and is 4 inches in diameter. Before beginning this repair make sure the power to the food waste disposer has been disconnected. This is an OEM part that is obtained right from the manufacturer.
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in diameter while the larger one is 2 inches in diameter. The hose clamps secure the end of the water hose in place to prevent the hose from le...Read moreaking. If you notice leaking from the hose of your appliance, you may need to replace this kit. Protect your hands with work gloves during this repair to avoid injury.
This is an elbow outlet and gasket for a food waste disposer or garbage disposer. This part connects the disposer to the drain pipe in your home. If you notice a blockage or a leak, you may need to replace this part. It is black in color, made of plastic, and measures about 6 inches tall.
This door key is a part for your chest-style freezer door handle. Your freezer will have a lid that locks and unlocks, and the function of this door key is to engage and disengage this lock. The measurements of this part are roughly 2 inches long, and 1 inch wide. If your key is lost or damaged, this is the OEM replacement part you will n...Read moreeed. We recommend that when you receive your key, you test it on your lock to ensure that the locking mechanism is working. Also, be careful to store your key in a safe place away from the freezer.
This support ring, also known as mounting ring, is a genuine OEM replacement part for use in food waste disposers. It is a circular plastic piece with an outer diameter of 4.75 inches. It is found inside the disposer housing where it provides support and stability to the unit. The ring helps to evenly distribute the weight of the disposer...Read more and waste evenly, so that the disposer does not fall out of alignment. Over time, the support ring may break due to the continuous grinding within the unit, and the exposure to moisture and waste. If the ring is no longer able to stabilize the unit, you will notice food and waste leakage, excessive vibrations, and damage to the disposer components. To begin this repair, first disconnect the disposer from the mounting assembly, and pull out the faulty ring. Place the new ring in its place and reattach the disposer to the mounting assembly.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
My refrigerator stopped cooling and the freezer section stopped freezing
441 of 556 peoplefound this instruction helpful.
garth from forest lake, MN
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck le
... Read moret's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!
Read less
Was this helpful?
Thank you for voting!
Deteriating splash guard
66 of 73 peoplefound this instruction helpful.
Brian from North Charleston, SC
Really Easy
Less than 15 mins
The splash guard for the disposer was deteriorating and kept falling into the disposer and getting chewed up making it even less reliable. I purchased two different 'universal' splash guards at the hardware store. Neither of them fit. I finally crawled under the sink with my eyeglasses and a flash light to find the model number. I se
... Read morearched for the model number on part select and received veery quickly. I just popped it in (less than a minute) and now everything is wonderful. Don't buy a new disposer (my wife wanted me to) buy the replacement part that is giving you trouble at PartSelect!