AFB2534DEB13 Amana Refrigerator - Instructions

first I looked into the refrigerator for blockage of air flow.
none found, I looked into the freezer area to see if fan was working ,it was, noticed ice built up on the outside of the metal cover letting me know it was not defrosting ,It was easier for myself to pull freezer door off , then the ice-maker,only three 1/4" hex head bol ... Read more ts,two 1/4" hex bolts only holding the metal cover . The quickest way to defrost was using a blow hair drier .once it was all defrosted I disconnected the defrost heater and using a volt/ohm meter,I ohm out the element,finding out I had no reading .The one thing I forgot to mention, unplug the frigertor first !!!

first I removed the pantry drawer and the 2 crisper drawers. Then I removed the glass shelf and it's supports. Using a nut driver I removed the 2 screws holding the end cap to the side of the refrigerator. Carfully snaped the end cap loose of the clip in front and pulled it straight forward, being carful not to break the rear tabs holding ... Read more the climate adjuster. I then removed the old climate adjuster from my broken part (it's held on by clips) and installed it on the new end cap. I put the new end cap in snapping it onto the existing clip and added the 2 screws. Put the shelf supports and glass back on top of the drawer, slid back in the crisper drawers, installed the divider into the drawer (it just slides in) then put the drawer back in and I was done. It was an easy job and I'm sure I saved at least one hundred dollors for 20 minutes work.

Not a bad job at all. Took out the vegetable bins above, the glass cover and the sliding drawer. Then took out the screws holding the end caps on to the refrigerator wall. You can remove the metal slide at this time or after you take the old piece out. Then you re-install the metal slide on the new piece and screw it back in. THe rig ... Read more ht hand side is trickier because you also have to remove the mechanism in the back that controls the humidity inside the bin as well as the control lever in the front, so that you can install them on the new end cap. All the parts either snap on or you have to twist them slightly. We repaced both end caps as well as cleaned things really well in about 45 minutes, with 2 adults and a 10 yr old working together.

1. I had to remove the cold cut drawer.
2. Remove the two screws for the sliding track and then the sliding track.
4. Remove the two crisper drawers as well as the glass and the two supports for the glass.
3. Remove the two screws for the end cap. This is accomplished by gently lifting up at the front of the part. You will ... Read more find another three parts that are attached to the end cap. One is the slider that controls the tempetature, it is attached to a long plastic rod that is connected to the back side of the end cap by pressure clip points. The other end of the plastic rod is connected to a piece that is mounted to the back wall of the refridgerator. this is removed by gently pulling the entire unit forward until it comes loose from the back wall. Once the entire assembly is removed, The plastic rod must be released from teh back of the end cap. This will allow both ends to be disconnected from the slider at the front and the piece that was attached to the back wall by rotating each end to allow the removal of the components fronm the end cap. Once everything is removed, you are ready to complete the repair by reversing the removal process.

I just opened up the fridge back panel accessed the old relay/capacitor, pulled it out, replaced with the new one, snapped it back into place, tested it (compressor came on), replaced the back panel and went on my way. Really, really easy repair.

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

The mullin requires only one screw removal, then LIFT the entire mullin upwards. Pop the wire harness loose, and replace with new mullin. Simple job,

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only ... Read more swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

Through out broken plastic, replace with new one
to be replaced in a few years.

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the c ... Read more ables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

Remove the light cover. Use a flat head screw driver to push in the tabs on the back of the program mount and pull down to expose the computer board. The Thermistor is clipped on under the vent holes on the right side. Cut both wires to remove the old thermistor strip a 1/4 inch off the remaning wires and the new thermistor wires twist bo ... Read more th ends together crimp on the wire caps snap in the new thermistor reinstall the program board until the retainer clips snap into place, slide the light cover back on.

Removed screws from cover tested for power to motor found power was on to motor but motor did not work. I went to your web site was able to locate part in about 5 minutes . Even with over night shipping the part came to about $50,00, far cheaper tha a service call would have been.

Thanks John Paulsell

Unpacked, inspected, found two minor defects in the form of two tiny slivers along the seal edge which I cut with a small scissor, laid the seal down on the kitchen table, applied heat to the deformed areas and reshaped them with my fingers, heated the entire seal lightly, removed the old seal starting at the right hand upper corner using ... Read more my fingers, installed the warm seal starting at the top corners by pushing it in its slot making sure the outer lip stayed out of the slot and worked my way around. I believe that the heat from the dryer made it pliable and easier to manage.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid