Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
I had a loose fitting old condensor fan blade on my new motor.
3 of 4 peoplefound this instruction helpful.
Roger from SMITHFIELD, RI
Very Easy
Less than 15 mins
Nutdriver
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a
... Read moresnap. Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Read less
Was this helpful?
Thank you for voting!
Water not draining to pan. It caused an ice build up under the freezer draw
3 of 4 peoplefound this instruction helpful.
Rich from WINSTED, CT
Very Easy
Less than 15 mins
Nutdriver, Pliers, Screw drivers
Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.
Was this helpful?
Thank you for voting!
I purchased a display model that was missing a part.
3 of 4 peoplefound this instruction helpful.
Monte from Longview, WA
Really Easy
Less than 15 mins
Snapped on the new toe grille.
Was this helpful?
Thank you for voting!
Center Crisper rail
3 of 4 peoplefound this instruction helpful.
Richard from PASADENA, CA
Really Easy
Less than 15 mins
Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.
Was this helpful?
Thank you for voting!
broke my original Kickplate Grille
3 of 4 peoplefound this instruction helpful.
Daniel from GEORGETOWN, TX
Really Easy
Less than 15 mins
knelt down, positioned replacement kickplate; popped into place, stood up!
took longer to open the box and peel bubble wrap off item than to replace it!
Was this helpful?
Thank you for voting!
Random clicking noise
3 of 4 peoplefound this instruction helpful.
Mark from SAN DIEGO, CA
Very Easy
15 - 30 mins
Nutdriver
The toughest part was pulling the refrigerator from the wall....After removing the back-bottom access panel the compressor is right there with the Start-Dev and Cap..Took a few min to remove and install new parts....Very Simple and works great...no more clicking..
Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattachin
... Read moreg rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!
Read less
Was this helpful?
Thank you for voting!
Refrig. was not holding proper temp in refrig compartment
2 of 2 peoplefound this instruction helpful.
Dan from Goldens Bridge, NY
A Bit Difficult
15 - 30 mins
Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the
... Read more4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.
Read less
Was this helpful?
Thank you for voting!
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
2 of 2 peoplefound this instruction helpful.
Marc from SEASIDE, CA
A Bit Difficult
30 - 60 mins
Screw drivers
I replaced the Control Board... the two boards need to be installed first . than plug in the connectors (refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work proper
... Read morely and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Read less
Was this helpful?
Thank you for voting!
broken right deli drawer guide
2 of 2 peoplefound this instruction helpful.
Herbert from MAHOPAC, NY
Easy
15 - 30 mins
Screw drivers
Removed old guide and installed new guide
Was this helpful?
Thank you for voting!
Refrigerator would stop cooling intermittently, control panel would not display temp settings until power was reset.
2 of 2 peoplefound this instruction helpful.
Jim from HALTOM CITY, TX
Easy
15 - 30 mins
Screw drivers
The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one or
... Read moreientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.
Read less
Was this helpful?
Thank you for voting!
FREEZEING UP
2 of 2 peoplefound this instruction helpful.
Sherril from ROBBINSVILLE, NC
Easy
15 - 30 mins
Nutdriver
in stalled new circuit board an thermostat an was fixed
Was this helpful?
Thank you for voting!
When the support frame broke we threw the entire system into the trash DUH !
2 of 2 peoplefound this instruction helpful.
Bruce from CLARKSVILLE, VA
Really Easy
Less than 15 mins
Thanks for the video showing how to replace the Humidity Slide the knowledge that the end with the flair needed to be slightly bent to SNAP into place was a big help.
Right Door Magnet weak, door would not stay firmly closed
2 of 2 peoplefound this instruction helpful.
Larry from CHIRENO, TX
Really Easy
Less than 15 mins
Replaced seal on door. Same problem. Went to Lowe's and got several magnetic cabinet door catches. Attached them to the top of the door. (they can be seen sticking up), with the magnet part screwed to the door and the metal plate attached to a small wooden block glued to the top of the body with contact cement. Cost abound $16.
... Read more> "To infinity and beyond."
My Orders
