AFB2234WEB3 Amana Refrigerator - Parts

This is a center crisper rail for your refrigerator. This part acts as a support rail for the crisper drawer by holding the center of the crisper frame. You will need to replace this part is if your current drawer is not opening or closing properly. This crisper rail is white and it is made entirely of plastic. It is roughly 13.5 inches long, and 2.5 inches wide. This is an easy repair which requires no tools.

This crisper drawer cover support is for refrigerators. Crisper drawer cover support supports the crisper drawer lid. Wear work gloves to protect your hands when installing this part.

This capacitor (Refrigerator and Freezer Compressor Run Capacitor, Run Capacitor) provides the voltage or energy current required to start the compressor and keep it running. It allows the compressor in your appliance to easily cycle on and off. This capacitor mounts directly onto the compressor starting relay. If the capacitor is faulty ...Read morethe compressor may get unusually hot and draw excessive amperage. It the compressor overheats, it may fail to run until it cools down again. The compressor may also get noisy from overheating. If this part is totally electrically open, it is defective (often due to overheating) and needs to be replaced. The part measures 1 inch by 1-1/2 inches, and is constructed of plastic with two metal wire terminals. This item includes 1 capacitor, sold individually. This part comes in black.

This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light when your fridge door is open, and to make sure it is off when your refrigerator door is closed. The reason you would need to replace this p...Read moreart is if your light is not turning on when your door is open. For this repair, you will need a putty knife, and a small flat-blade screwdriver.

This is an OEM front cover for the pantry door of various refrigerator models. This cover is designed as a door that can cover the pantry compartment within your refrigerator and provide a transparent view of what is inside it. If this door is cracked, moldy, or missing, it needs to be replaced. This pantry door is made of durable white p...Read morelastic and features a transparent window in the middle. This measures approximately 28.5 inches wide and 6.75 inches deep, and can be replaced by simply dislodging its securing tabs on the left and right side, and then inserting the new one into those same tabs. This pantry drawer cover is sold individually.

Sold individually.

The p-trap drain tube kit may also be known as the duck bill, or the drain pipe, and it is compatible with your refrigerator. The function of the p-trap drain kit is to carry the water that has formed during the defrost cycle to the bottom of the refrigerator, where your drain pan is located. The tools you will need for this repair includ...Read moree a 1/4-inch nut driver and a small flat-blade screwdriver. To do this repair you will need to pull the refrigerator forward in order to reach the lower access panel at the back. This kit includes the tube extension piece and spacer.

Sold individually. Crisper drawer is an original equipment manufacturer (OEM) part that fits some bottom-freezer Kenmore, Amana, Crosley, Jenn-Air, KitchenAid, Maytag and Whirlpool refrigerators. The crisper drawer is approximately 6-7/8-inches tall, 14-inches wide and 15-inches deep.

The electronic control board is used in refrigerators to monitor and manage the temperature settings, such as cooling or defrosting times. If your fridge or freezer is too warm, too cold, is not defrosting, will not start, and/or runs too long then replacing the control board could solve your appliance problem. The tools needed for this i...Read morenstallation project is a small flat blade screwdriver. *Please note: the board will need to be programmed after installation. Remember to unplug refrigerator from power source as a safety precaution. Refer to the manual provided by the manufacturer for further installation instructions and accurate guidance.

This refrigerator shelf frame is designed to support the glass shelf positioned above the crisper or pantry drawer, helping to keep your fresh food items organized and easily accessible. Crafted for durability and a precise fit, it is compatible with a range of refrigerator models. Please note that this listing includes the frame only; th...Read moree glass shelf and center support are not included and must be purchased separately. Installation is straightforward—simply remove the old frame and slide the new one into place to restore the functionality of your refrigerator’s storage space.

This is a light switch for your refrigerator. It activates when the door of your appliance is opened, and it will turn the light inside on and off. You will need to replace this part is if your light is not working properly. In order to make this repair you will need a Phillips screwdriver, a pair of needle nose pliers, and a small flat b...Read morelade screwdriver. This light switch is almost 2 inches long, 1.5 inches wide, and just over an inch thick.

This is a deli drawer glide for the right side of your refrigerator. It allows the deli drawer to glide in and out smoothly. In order to access your glider, you will have to remove drawer and shelf, and unscrew the existing screws. Reverse and reinstall. This part is approximately 14.5 inches long, and made of white plastic.