AER582 Amana Range - Instructions

I discoverd my switch box locked with my stove electrical port and stove stopped functioning. Pulled my stove back and saw that the "terminal block" was melted on one side; hence, switch box locked in place to avoid a fire, thank goodness. Looked up part on internet, unplugged stove, took off terminal box, ordered part and replaced. BT ... Read more W - PART SELECT is awesome; I received my part the very next day!!! :-) Very happy with their service.

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I re ... Read more moved the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

I cut the ends of the cord and went with direct wire (no round eye clip) to the back side of the terminal block and tightened firmly. It took about 20 Minutes.

Turned off power.Removed 2 screws, flipped top over, removed old element, replaced new element,turned over top,fasten down with 2 screws.Turned on power. Turned on burner,made coffee-took a brake.

Unplugged the range.
Removed the screws holding the flat top from the front bottom (inside doorway)
Unplugged the two connects at the back and removed the ground screw.
Unscrewed the bar holding the elements and remove the element.
Replaced with new element. Installation is reverse of removal.
Very easy if you ar ... Read more e careful..Always unplug your appliance before working on it.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturda ... Read more y and was cooking with it on tuesday. Great job.

I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...

ordered new front and replaced

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

My oven was assembled at the factory with half a hinge in left side ( no giant spring assembly) and in 15 months the right side hinge twisted and collapsed from bearing all the weight. First I thought I was only dealing with one bad hinge, and took the screws out of one side of door only and replaced hinge and was done in five minutes. W ... Read more atched YouTube videos which were great and did the repair . Then I noticed the other hinge had no tension on it and did a complete disassembly of door and compared hinges and discovered the other shoddy assembly. I recommend you try to replace one hinge at a time. Take out screws on one side and finagle hinge into place. I did not do this and it took a long time. Rated repair difficulty due to several parts of oven door need to be aligned correctly to get the screws back in. Getting one side aligned caused the other side to become mis-aligned. Not rocket science but requires a lot of patience as you will redo it many times. I screwed the new hinges/steel channels they sit in into the inner door to help reduce the number of moving parts. Then aligned and secured door parts. I cut a 6” piece of straight wire from a coat hanger and stuck it through the screw holes to line them up. Worked very well, and after door was screwed together then I finally screwed the hinges to the outer door.

Purchased 2 piece broiler pan from this site