AER1 - Instructions

It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.

First thing- I cut off power to the range. I then removed two screws to allow the cook top to be lifted. I marked the wiring and replaced the burner. Reapplied power and started cooking!

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

Piece of cake! Took more time to find the screwdriver than it did to replace the element!
Unplugged the stove. Removed 2 screws. Pulled the element out about 2" and disconnected the wires on each end (wires are attached to a metal clip that just pushes on to the end of the element. Threw the old element away. Unpacked the new el ... Read more ements. Connected the wires at each end. Pushed element into place and screwed in 2 screws. Plugged oven/stove back in and voila! That's it!

This was a complete no brainer. The easiest repair I have ever done. Take out the old screws, remove element and replace with new one, replace screws. Took less than 5 minutes :)

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

I ohmed out the burner element that wasnt working and found it was open. I ordered a new element thru PartSelect and installed it in the stove. I powered up the stove and turned on the burner but it didnt get hot. After a bit of testing I found that the new elements safety overtemp terminals werent in the same configuration as the origina ... Read more l unit. I made some wiring adjustments and the burner was operating properly. Thanks PartSelect

Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power ... Read more and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.

just replacing the new one into place manually!

I just bought my first condo and sure enough something broke in my oven. I thought "Oh great - I'll need to buy a new one..." After some research and a friend's advice - I was assured that I only needed to replace the broiler element. After researching the issue I googled replacement parts which led me to this web-site. I was amazed h ... Read more ow easy and inexpensive it was for me to replace the part. The directions were easy, simple, and spot-on! The instructions that were provided were easy to follow. I also utilized YouTube instructions as well for additional visual guidance. The shipping was super fast and the element was packaged very well. Thank you so much!

Shipped on timely manner,I will order again from Part Select, installing was a 15 minute job, that what I did, 1 unplugged stove, 2) removed 4 screws, (2 on top bracket and 2 on back) , 3) slide unit out couple inches enough to disconnected the wires from each end of unit and removed old part, installed new unit by reconnecting end wir ... Read more es, pushing unit slowly toward back of oven until wires find it's right position, set it back in place with the 2 screws on top bracket and 2 screws on back, done!!

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

My wife and I did the repair. The most difficult part was finding the correct replacement part. The store where we bought the stove lied about what part was needed, which cost us a lot of online time before we found the part. UNPLUG THE STOVE or turn off the breaker. We removed the back of the stove, which is two or three pieces, comple ... Read more tely. The thermostat is part of the single oven control. This job inclludes replacing the oven thermocouple (temperature sensor) which is a small copper tube about a foot long which is inside the oven itself,held in two spring clips on the left upper side near the front. You install the new thermocouple, which comes with and is attached to, the replacement thermostat from the back and top of the stove. Unplug the top burner elements and remove them, along with the drip pans. Remove the single screw that holds the connector for each burner to the stove top. Then lift the front of the stove top and remove it. Remove the screws holding the inner top of the stove. It has a tab on each side that slides under the flange of each side of the stove, so you must remove all the screws from the back of one side so you can swing it out a bit. Then you can remove the inner top, Under that is insulation covering the top of the oven. Remove the old thermocuple. It is easier to cut it instead of fishing it all the way back. Just be careful to note how it is installed. Silde the new thermocouple in from the thermostat, under the insulation and through the small hole in the top of the oven box and clip it in place. The clips are flimsy so support them as you remove and install the part. Hold the new thermostat right next to the old one BEFORE you disconnect any wires. Unplug each wire in turn and plug it into the new thermostat before going on to the next wire. Watch for the short wire that connects from the thermostat to the oven indicator light. Then remove the old thermostat and put in the new one. Reverse the steps of the disassembly process to get it all back together. Be sure the insulation holds the thermocouple in the center of the hole mentioned above. That's it. Be careful of the sheet metal parts of the stove; Crosley didn't bother to deburr them and they can give you a nasty cut. Reconnect the power and test. If it all works, maybe you can talk your wife into baking something.