Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Leaks onto floor from lower section
2 of 2 peoplefound this instruction helpful.
Bernice from New Vernon, NJ
Really Easy
15 - 30 mins
First I replaced the door gasket as every one else. This cut drips about 30%. I then discoverd that the Rinse Aid circular dispenser cap was opened about half way. I turned the cap tightly clockwise to close and cut drips to 90% total. I czn live with the other 10%,
Was this helpful?
Thank you for voting!
After 22 years of virtually trouble -free service, I could tell by the sound that something was wrong. Water fill ran too long. Float not stuck. Checked and found float switch stuck.
2 of 2 peoplefound this instruction helpful.
Marc from GLENDALE, NY
Very Easy
15 - 30 mins
Screw drivers
Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P
... Read more.S. Don't forget to turn power off to dishwasher any time you work on it!!
Read less
Was this helpful?
Thank you for voting!
Lower left corner of the door was leaking every so often.
2 of 2 peoplefound this instruction helpful.
Frank from Ridgefield, CT
Easy
15 - 30 mins
Screw drivers
I first made sure the new gasket was long enough and it matched the original. Next I used the tip of a screwdriver to pick out a corner of the old gasket and then pulled the entire thing out. I noticed the old one stopped at the bottom of the gasket well. The new one was much longer and I thought I might have to cut it to length. Well I'm
... Read more glad I didn't. If you start on the right side and work your way up and around with a 2 in. piece longer then what the old one was. I carefully tucked it in the bottom and closed the door. Glad I didn't cut the new one. Instructions would have been nice. Overall an easy fix. I'm very mechanically inclined so I knew better.
Read less
Was this helpful?
Thank you for voting!
ratteling noise
2 of 2 peoplefound this instruction helpful.
gregory from Staten Island, NY
Easy
Less than 15 mins
Nutdriver, Screw drivers
unscrew screen and cover and unbolt impeller replace with new parts. everything goes back together easily, anyone with even minimal repair skills should be able to do this repair.
Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!
Was this helpful?
Thank you for voting!
My dishwasher was leaking from the bottom right hand corner.
2 of 2 peoplefound this instruction helpful.
Teresa from Terre Haute, IN
Really Easy
Less than 15 mins
I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.
Was this helpful?
Thank you for voting!
washing machine leaked at right lower corner
2 of 2 peoplefound this instruction helpful.
joseph from goffstown, NH
Really Easy
Less than 15 mins
removed old deteriorated gasket - just pulled out cleaned soap particles from door seal area pressd in new gasket - note orientation done.
still leaks - will investigate further
Was this helpful?
Thank you for voting!
My old silverware basket was wearing through on the bottom and silverware was sticking through
2 of 2 peoplefound this instruction helpful.
Bonnie from OREGON, OH
Really Easy
Less than 15 mins
Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring sp
... Read moreoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!
Read less
Was this helpful?
Thank you for voting!
leak at bottom left and right side
2 of 2 peoplefound this instruction helpful.
Bernadette from Glen Cove, NY
Really Easy
Less than 15 mins
pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.
Was this helpful?
Thank you for voting!
Leaky door
2 of 2 peoplefound this instruction helpful.
George from Whitinsville, MA
Really Easy
Less than 15 mins
Screw drivers
Removed old gasket and simply replaced it with the new one. Very easy.
Was this helpful?
Thank you for voting!
bottom of utensil basket broke away
2 of 3 peoplefound this instruction helpful.
Lawrence from Palm Springs, CA
Really Easy
Less than 15 mins
Took out the old basket, Threw it away. Popped in the new baskey, filled it with forks and spoons. Works great!
By the way, my order arrived in one day. Phenomenal!
Was this helpful?
Thank you for voting!
Old dishrack was rusting apart
2 of 3 peoplefound this instruction helpful.
Barry from OCEAN, NJ
Really Easy
Less than 15 mins
Pliers, Screw drivers
First you must understand that the end cap is not a solid piece. The plastic facing you is wrapped over the piece behind it. The separation may be obscured by age. Wedge thin bladed screwdriver into the outside edge of end cap at the bid point, a sturdy hunting knife will probably work better. When you hit the seam, pry it apart and f
... Read moreold it back. Unwrap the part and repeat on other side. The dishracks will easily slide out and in.
just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .
Was this helpful?
Thank you for voting!
spring linkage broke, dishwasher door droped like a rock
3 of 6 peoplefound this instruction helpful.
Timothy from Westford, VT
Really Easy
Less than 15 mins
Screw drivers
removed 2 screws that anchors the dishwasher to the counter top, slid the dishwasher out. Only one of the linkages was broken but because of the age, I replaced both door springs and door spring linkages.
My Orders
