ADG7 Admiral Dryer - Instructions

Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

I inserted the clip

Removed bottom door panel, four screws. The new part was a slightly different (looks like improved) part, so only had to put two screws back in. Very simple. The only reason it took more than 15 minutes was because I cleaned exposed areas while the panel was off.

unplug dryer, lift top, remove 2 screws holding front, lift & swing front to right, use nutdriver to remove two screws holding igniter and other piece attached with same screws, a couple wiggles and out, unplugged igniter, plug in new, reposition new igniter and other piece, replace screws, repositioned front panel, replaced front panel s ... Read more crews, dropped top back in place, plugged in and wha-la. Heat.
Original Igniter had a hairline crack in it causing it to intermittantly fire. Thanks PartSelect, right part and speedy delivery.

Easy Job.
First take a flat head screw driver and pop the top placing the screwdriver in between the front panel. The top of the dryer should pop up.
Then just pull it up and over towards the back.

Then unscrew the front panel and move it out of the way leaveing the front door atached to the panel.
Once you ope ... Read more n the front panel' You can pull the dryer tub out by sliding it out and at the same time you need to push the belt towards the back of the tub until it comes off.
Now you can get to the ingiter by first disamablethe gas
housing first.
Simply by taking one screw off and disconnecting the gas line fitting in front of the dryer. Also disconnect the 3 sets of wires that are connected to that piece and the igniter.
The hole piece will then come out with the igniter attached to it.
Next disconnect the igniter from the piece and replace it with new one.
Then put back togather the same way you took it apart.
Reinstalling the tub.
When it's time to put the tub back in; there's a trick to that.
Put tub in about 3/4 of the way in, put the belt around the tub and let the rest hang to the floor inside dryer.then crawl into the tub and stetch your head and arm through the tub on the back side.
Then you can get to the belt and route it into the motor and the pully that is spring loaded it makes it so much easer that way then trying to run the belt and route it in place from the top. Once that is done now you can adjust belt back to its orignal position then push the tub back in place. Reinstall fron panel and your their.
Total cost 36.00 plus shipping. Thats a lot cheaper then a sevice call and labor

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

First off I want to say I ordered my motor on Sunday night at 11:30 PM on veterans day and got the two day delivery. My part was sent out on that Monday (fed. holiday) and I received it Tuesday around 1:00 pm after I disconnected the wiring harness, took the blower fan C-clips off, unscrewed about 6 screws, and pulled the assembly apart I ... Read more just done everything in reverse and replaced the new motor. I discovered that my thermostat fuse was blown so I ordered the High temp thermostat kit from here (two day delivery) on Wednesday at 10:30 PM and got the parts Friday at around 2:00 PM. After taking out four screws and four wires I replaced the fuse and high temp. set, pushed the start button to see if it worked and it started up like new. Now it heats twice as fast and everything doesn't have a light burnt smell. So dry time is faster (no more 80-90 min. cycle times), less dryer sheets (to cover smell) and all this added up to cost savings on electric bill and dryer sheets. It took a week to get my dryer back (because I just looked at the motor) but in the end I needed the fuse and motor. The quick turn around time to get the parts, the pictures to see if I had the right parts, and the ease of ordering the parts meant only one run to the laundry mat, and that wouldn't have happen if the dryer hadn't messed up on laundry day.

Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the fron ... Read more t holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

I applied the excellent description of accessing and fixing the drier givenby others. When the second fusible link opened, I consulted the Repair Forum. Denman, an obviously experienced responder, walked me through the diagnostics.

I did not ask denman's permission to pass on his recommendations so they may or may not apply ... Read more to your situation. Heere

"Here are your parts with a wiring diagram
Maytag YE225LV

With the unit apart and drum/belt removed and thermal fuse wires shorted together the motor should run. You also have to tape or hold the door switch closed. I would also disconnect and tape up one of the wires going to the heater coil as it will overheat. Never leave the thermal fuse shorted as the unit can cause a house fire without it.

Be very careful that everything is well taped up so you do not get a short.
You have 220 volts in the unit which is very dangerous.

The motor should manually turn easily from the pulley end.
The ding from the fan indicates that there is a problem here. Check it carefully.
Here is a good site
Dryer Help Sections, repairing dryers, Kenmore, Whirlpool, Maytag, Inglis, GE, Frigidaire, White Westinghouse, Magic Chef, Norge, changing a 3 prong cord to a 4 prong cord, no heat, electric dryers, gas dryers, how to take apart my dryer, what can st
Check out the Maytag Dependable Care section / 26 -motor problems / "Check this out" at the bottom of the page

Normally your high limit safety thermostat should open before the thermal fuse blows.
When you ran your test did you run it on fluff (no heat) at first?

I would remove and check the heater for a grounded element.
Depending where it breaks/shorts it can be on high heat all the time with the thermostats having no control of it.
From your description this would be my prime suspect!!"

My observations:

1 the reference above is to applianceaid.com, which had useful tips. Tip #4 was washing the filter screen with detergent, as it holds an invisible layer of residual lint.

3. When cleaning, disconnect front panel, take out filter and clean the cavity behind the filter. I used a garden hose and large volumes of lint came out.

Now I am scheduling full clean out at least annually, including washing screen and inside door.

2. since thermal fuses are designed to open when overheated, it is hard to test if they work or not. (They test continuous at room temperature.)

3. at Denman's subsequent suggestion, I replaced the thermal fuse past the blower. (There is a thermal fuse ahead of the heating elements and the elements heated, so it is a less logical failure candidate.)

System working fine. The help was worth as much as the parts!

Not too difficult. Take out of box, insert into dryer slot.
Done

Before anything else, I would like to thank your company for a quick response and fast delivery of the parts that I ordered. Ordering parts from your company saved me a lot of money. The repair took me about 15 min. First I removed the two screws that hold the front cover and then I pulled out the drum and replaced the broken pulley, th ... Read more en I put back the drum and the belt in place and then I put the cover and screwed back in and now I'm back washing and drying pile of clothes.

First I went to Maytag.com thinking it was best to go to the manufacturer for parts. Their search engine did not even recognize my part number. I tried every way I could think of. Then I just entered the model number in google and it sent me to the Partselect.com website. Diagrams came up and I chose parts from the pictures. The parts arr ... Read more ived in about 3 or 4 days and fit perfectly.

Replaced the recommended drum rollers, belt and tensioner, light bulb. Found repair manual online (bit of a hunt)made job easier still took 2.5 hrs. Then turned drum by hand no squeak. Turned it on and still squeaked. Isolated to motor. Replaced it (had to take dryer completely apart again but went quicker due to experience also had to ... Read more disassemble the motor assy and rebuild. Took 1.5 hrs works like new now. The design of the dryer is not bad remove bottom front panel first, screws at very bottom of panel then two more screws are uncovered to remove front. It just lifts up and pulls out. then remove four bolts which hold front frame on (supports drum) all this has to be done to reach the replacement parts. drum wheels are held on by snap rings not the screws (real fun if you take them out) reverse to reassemble.

Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and da ... Read more rkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .