ADG3 Speed Queen Dryer - Instructions

Repair was easy, remove bottom cover, remove screws that hold coil bracket, remove old coils & slip new ones on & button up. Dryer works fine now.Had the new parts within 3 days. Thanks PartSelect!

easy as pie !

Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.

It was a fairly simple repair to perform with the dryer in place. I simply opened the bottom/front access panel to start, the door removes if you pull up after opening. Then I disconnected the two and three wire connector to the two coils. Next I removed the bracket screws that fasten the coils to the valve assembly. This was a little ... Read more difficult with the screw closest, because of the small clearance and #1 sized phillips(stubby would work well.) The rear screw I managed to remove by using both a small flathead screwdriver(hex shaped shaft) and an adjustable cresent wrench. At this point, it was a simple matter of installing the new coils and the bracket, and then reconnecting the two plugs. It almost made me want to do laundry.

Parts came as ordered and in really good time. The valves were very easy to install, just a matter of removing lower housing and the two screws holding in the old valves. The plug and play, no calibration needed and the dryer works like new. Very easy fix and the instructional videos were very helpful. Saved a lot of money doing it myself ... Read more .

Opened the dryer door - removed two screws on the left and two screws on the right - pulled the front panel forward and lifted it up to remove. The coils were located on the bottom right hand corner of the dryer, I vacuumed he area and then removed the two screws and bracket which hold the coil in place. Lifted the new coils off paying cl ... Read more ose attention to their orientation. Installed new coils. Align tab on top of coils with bracket. installed bracket and screws. Tested dryer and then replaced front cover. Very easy and rewarding.

open the back pannel and use multimeter to check the wirings and everything checks ok. open the bottom front panel of the dryer and turn the dryer on. the igniter works and the flame came out for seconds and dies off. the igniter keep coming on, but it seems that the gas was not coming out. i checked the gas line valve and it was open. i ... Read more had a good idea it wasn't the wiring or the gas line, it must be the coil-valve,(safety coil), that letting the gas flow. i order the parts, it came sooner, which is good, and it took me less than 10 minutes to install, and i only use a philip screw driver. i thank you for sending me the right part in short period of time.

Found symptoms on Part Select website and confirmed that the problem was the coils. It was extremely easy to find and the site saved me hundreds of dollars on a repairman, labor costs and marked up parts. It literally took about 5 minutes to repair. Awesome site!!Thank You

Unplugged the dryer from the wall. Removed the front lower cover. Removed the two screws for the bracket that holds down the coils. Unplugged the coils and swapped them out. Reassembled everything in reverse order. Plugged the dryer back in and started it. It's as good as new.

Checked heating element and it glowed so I replaced the ceramic gas valve regulators. 4 screws to take front off the dryer and 2 screws to replace part. Couldn't have been easier but I wouldn't have been able to do it without watching the video first.

Remove the two screws holding the door and lift straight up. Remove the two screws on oppostie side. Face can now be removed by pulling straight out at the top, then lifting face up off of tabs at the bottom. The two coils are at the bottom, held in by a retaining bracket. Remove the screws that hold the bracket. Replace the coils by ... Read more unplugged their wires. That's it!

two screws on lint screen push up top two screws on front cover. two screws on coils lift coils off put back together. less than 10 minutes. all done

Removed two screws from front panel and lifted front panel away, Turned it to the left so I could keep the door switch connected. The dryer would heat when it was first started, but then the burner would go off and would not come back on. I ran the dryer with the front panel off and could see the igniter glow and light the burner, but ... Read more after the burner cycled off, the igniter would come back on but the gas would not come back on. I could tell it wasn't the thermostat because the igniter would come on, so I knew it must be the gas valve, and therefore probably the coils. The instructions on the website said that the coils were frequently intermittent, so that seemed like the problem. I tried checking out the coil resistance with an ohmmeter to try to confirm that, but couldn't really tell anything that way. I ordered the replacement coils Tuesday night, selecting the cheapest shipping; they shipped on Wednesday, and were delivered on Thursday! Amazingly fast! Removed two screws from the clip that holds the coils in place, unplugged the old coils, swapped in the new coils, screwed the retaining clip back on. All done. Before I replaced the front panel, I watched to see that it operated correctly. I could see the burner cycle off, then after a bit, the igniter glowed, and then the gas came back on and lit, just like it should. Problem solved. Put the front panel back on, and that's all there was to it. Well, I did vacuum out some of the dust inside the cabinet while I had the cover off. Just out of curiosity, I checked the resistance of the new coils before I installed them to compare with the old ones. Couldn't see much difference.

replaced the two coils, which took about 10 minutes

Followed videos seen on the internet for my dryer's repair. Went exactly as shown.