ADE26K3H Admiral Dryer - Instructions

Before ordering the part, I found this website by linking from a video on YouTube where several people showed how they did it. Simply two screws in the lint removel chute and pushed in the two clips holding the top and two inside screws holding the front panel. Held the machine tilted back onto a table and placed two 4" wooden cubes underneath it so it wouldn't come forward and one more 4" cube under the drum. After cleaning out the inside, I slipped the new belt around the drum (ribbed side down) and taped it in place with a couple of pieces of painter's tape temporarily. Hooked the idler wheel guide and looped the belt in it. Tested movement by spinning it by hand to check alignment and removed tape. Reassembled the front, side and top panels accordingly and tested it. Voila! This was my first attempt and I saved myself some bucks. The last repair was done by Se•rs and their service person took my credit card number for the invoice and promptly went out and charged over $3,000 on it. He was eventually caught. Great incentive to do yourself, huh?

i pop the top of the dryer lose and removed the 2 screws that held the front on and installed the new belt and put it back to gethere

First, I printed one of these responses which were excellent and very detailed. The screws connecting the lint slot to the top of the dryer was frozen. Taking the front panel off was difficult because I did not read the instructions I printed out very well. After I took the top off I had a hard time finding the 2 screws located inside on the top of the front panel. They are located to the far right and left at the top. To take off the front panel you have to push it up to release the clips on the bottom, then it comes right off. Taking the drum out was easy. What was difficult was putting the belt on. There wasn't any slack and to put it around the pulley and the drum for me was difficult. After that is was a piece of cake. It works great.

Dont go in through the back!! Take the top off then the obvious steps to get to the drum and belt. On the kitchen aid model at least I would advise to make all the hassel of replacing the belt well worth your time to go ahead and buy a new tension pulley with the wheel on it as opposed to the all metal tension pulley. My dryer is much more quiet now and seems to be more efficient.

I waited a two days to get my belt then deciced to get a new tension pulley. Ordered it one day and the next it was at my door. This was well worth my time and effort. Thanks PartSelect!!

Pry up front of top and lay back. Remove two 1/4" srews at top corners. The front of dryer will then swing to the right. The drumb will lift out easily. Remove broken belt. Inspect the drum rollers on the back wall. Replace if loose or not turning. Mine needed replacement. The assembly part is not easy. You need the drum in place and after it is in place you can't get the belt on. After 8 tries I got smart and made a prop to hold the idler pully up, then put the belt in place and let the pully down slowly. It worked! Put the front back on and the 2 screws and pop the top back down. Also it is a good idea to unplug the electric cord and turn off the gas (if app).

- Unplug the electric dryer.
- Manually opened the top of the dryer.
- Unclipped the wire assembly attached to the front panel of the dryer.
- Removed two screws holding the front panel of the dryer, and remove front panel for access.
- Very Important!! Note how the old dryer is currently installed before proceeding.
- Rotated the dryer drum while working the dryer belt toward the rear of the dryer.
- Removed the dryer drum.
- Removed the old dryer belt.
- Put the new dryer belt around the dryer drum and put the dryer drum back onto the drum rollers and into the rear guides.
- Here's the hard part, lay on floor and reach into the pulley area and motor - wrap new dryer belt around these belt rollers as "noted" in the fifth step.
- Rotate dryer drum by hand to ensure the new dryer belt is exactly installed as the old dryer belt.
- Reinstall front panel.
- Reclip wire assembly onto the front panel.
- Manually close the top of the dryer.
- Plug in the electric dryer.

Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)

Step 2. Read the directions that come with the dryer (they helped a lot)

Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.

Removed the two screws holding in the Filter and removed the filter.

Removed the two screws holding the front onto the dryer.

Put the belt over the drum and proped the drum up.

Reseated the tension spring and pully in the proper slot. (On my machine it is the position closest to the motor).

Reassembled the dryer in the reverse order.

-Took top of by prying with screwdriver.
-2 screws and door wire to take off front panel.
-proped drum with 4X4 piece of wood.
-looped belt around drum where the mark for the old belt was.
-looped belt through tensioner and pulled with the screwdriver over the motors drive shaft.
-manually spun drum to make sure everything was right.
-put panels back on and was done.

You cant go wrong with the included directions and belt diagram. this is the first repair I've done of any kind that went flawless.

first I took the two screws that hold the filter in, then disconected the power,then I poped the top of dryer up and removed the two 5/16 screws on the inside of the front panel then the two screws down by the loading door hinges and took off the front cover and the drum, replaced the belt and put the ajuster back on and put everything back in revers order and it is working like new thank you for the fast order .tony

first, i read all the comments on this web site as well as other web site. sooner i confirm the problem is the drum belt, i order the parts.
my kemore model front panel is one piece. so i have to lay down the dryer and open the front panel on the top. The instruction sheet sent with the belt is very good, so it does not take too much time to replace the belt, the challenge task is to reconnect the front panel to the side panel. I spend too much time trying different way to use the fastner hook to connect panels without realizing that the hook is broken. stupid me. i later have to use the wire to connect the front panel to side panel. overall, i am very happy i fix the dryer.

I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.

Pull dryer out from wall about 6 to 8 inches step 1 - romove front/bottom access panel. Step 2 - remove lint trap and remove 2 screws (philips type) that is under lint trap door. Step 3 - push in 2 wood shime in front edge between lid and front panel (angled shims like door shims - a putty knife will work to, just be carful not to scratch finish) step 4 - fold lid upward and back (like on a hinge) step 5 - looking from where the bottom/front acces panel was losten 2 screws - one left one right about 3 turns - 9you can remove them it just makes it easier to reinstall the front panel. Step 6 - find appropriate pot or stacked 2 x 4 pieces - something to hold up the drum when you remove th front cover, and from underneeth support the drum. Step 7 - look thru bottm front access hole - there are 2 springs that come down from the door - and clip onto the frame of the fryer - unclip them and place on the side. Step 8 - remove 2 upper screws that hold front panel on, and remove front panel, if you left the bottom screws attached but loosened you have to lift up on the front panel a bit. Step 9 - looking from the bottom thru where access panel was - you will see motor on right with a additional roller (tensioner) - push upwards on tensioner to relieve pressure on motor and pop off belt (remember where tensioner is and how it clips in to base. Step 10 - work belt off of drum towars front - to remove it all the way you will have to lift up the drum slightly off of the pot or whatever you used for support so the belt can clear. Stem 11 - new belt goes on the same way you took to old one off - plat side away from drum with ribs against drum. Step 12 - again lift up on drum and work belt back on. Step 13 - tricky part is how to get the belt back on the motor - prentend you are threading a needle wht a folded over piece of thread - hold the belt with about a 4" loop with your left hand - hold up on tensioner and feed it back thru and work belt back over end of motor pulley, after front panel is back on with the 4 screws tightened spin the drum and make sure belt is between the 2 lines marked on the drum and remove the pot or whatever u used to prop up the drum. Dont forget to attach the springs for the door assemble all other components in reverse order. And dont forget to take the pot back out