ADE20L4H Admiral Dryer - Instructions

I applied the excellent description of accessing and fixing the drier givenby others. When the second fusible link opened, I consulted the Repair Forum. Denman, an obviously experienced responder, walked me through the diagnostics.

I did not ask denman's permission to pass on his recommendations so they may or may not apply ... Read more to your situation. Heere

"Here are your parts with a wiring diagram
Maytag YE225LV

With the unit apart and drum/belt removed and thermal fuse wires shorted together the motor should run. You also have to tape or hold the door switch closed. I would also disconnect and tape up one of the wires going to the heater coil as it will overheat. Never leave the thermal fuse shorted as the unit can cause a house fire without it.

Be very careful that everything is well taped up so you do not get a short.
You have 220 volts in the unit which is very dangerous.

The motor should manually turn easily from the pulley end.
The ding from the fan indicates that there is a problem here. Check it carefully.
Here is a good site
Dryer Help Sections, repairing dryers, Kenmore, Whirlpool, Maytag, Inglis, GE, Frigidaire, White Westinghouse, Magic Chef, Norge, changing a 3 prong cord to a 4 prong cord, no heat, electric dryers, gas dryers, how to take apart my dryer, what can st
Check out the Maytag Dependable Care section / 26 -motor problems / "Check this out" at the bottom of the page

Normally your high limit safety thermostat should open before the thermal fuse blows.
When you ran your test did you run it on fluff (no heat) at first?

I would remove and check the heater for a grounded element.
Depending where it breaks/shorts it can be on high heat all the time with the thermostats having no control of it.
From your description this would be my prime suspect!!"

My observations:

1 the reference above is to applianceaid.com, which had useful tips. Tip #4 was washing the filter screen with detergent, as it holds an invisible layer of residual lint.

3. When cleaning, disconnect front panel, take out filter and clean the cavity behind the filter. I used a garden hose and large volumes of lint came out.

Now I am scheduling full clean out at least annually, including washing screen and inside door.

2. since thermal fuses are designed to open when overheated, it is hard to test if they work or not. (They test continuous at room temperature.)

3. at Denman's subsequent suggestion, I replaced the thermal fuse past the blower. (There is a thermal fuse ahead of the heating elements and the elements heated, so it is a less logical failure candidate.)

System working fine. The help was worth as much as the parts!

First I removed the screws that held the part in place, but this proved to be the hardest part for me. I had to find the right kind of screw driver . It was not a slotted or Phillips. It was more star shaped. Once I had the right tool, the rest was pretty easy.
I then opened the top of the dryer to be able to lay the front on th ... Read more e floor. There were wires connected to the front, however, so I had to remove the part that the wires were connected to by slipping it out of the bracket that held it in place. Once the front panel was on the floor, I simply lifted the old part out and placed the new part in. I closed the front, replacing the part with wires back into the bracket, locked the top down tight, replaced the screws, and I was finished.

1st thing,,,,unplug dryer from electric,,,Raised the top of dryer, took 2 screws out that held front of dryer on, removed 3 wires and dropped front of dryer. exposed blower wheel,, removed all nuts holding front of blower wheel, removed clamp on front of wheel with pliers, removed old wheel, replaced everything in reverse.

After reading the comments of on-line customers, I realized the dryer opens like the hood of a car and then you pull the front of the dryer door off in order to get to the two screws holding the old lint duct housing unit. Putting the new part on was easier, but I would have appreciated a detailed picture along with the written instructi ... Read more ons. Thank you for your quick delivery. Kathleen Yosso

Was obvious what the problem was when dryer lost heat. Thermostat was fried with one contact burned off.
Unplugged dryer
Opened top of dryer using putty knife to release latches.
Removed 2 wires to Therostat, and removed the old one (2 1/4 hex screws).
Installed new thermostat, and reconected.
Done

First lift the top and remove 2 screws holding the front panel on, at each top corner. Release the door switch from its clip (or disconnect the wires). Remove the front panel by tilting out and then lifting it up off the bottom tabs. Remove the belt from the motor by releasing the tensioner. Then lift the drum out. Remove the front blower ... Read more cover, then remove the tensioner by first removing the spring, then pull the tensioner out toward the back. Remove the strap on the back of the motor near the pulley. It takes a little effort to get the strap off. Remove the 3 bolts holding the blower case (with the motor still attached. Remove the motor wires, then lift the motor and blower case out. Next remove the clip holding the blower fan on and remove the fan. It may be stubborn so be patient and slowly work it off. Remove the next clip behind the fan. Then remove the motor from the blower case by turning it counter clockwise (as viewed from the motor side). Installation is the reverse.

Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Pro ... Read more blem!

Unplugged electric, turned off gas valve. Opened top using a putty knife, laid it gently back against the wall for support. Removed 2 screws holding front on-leaned front out about 3-4 inches- while holding front with my knees I disconnected door switch wires.-then removed front panel. Followed instructions on maintenance sheet glued o ... Read more n underside of dryer top (Lucky it was there). Took tension off drive belt. Removed belt and drum following instructions on lid sheet. Removed old slides (worn out) Installed new pads & slides. Vacuumed out all lint/dust/dirt I could reach, Cheked rear drum rollers. Reinstalled everything that I had removed. It took extra time to do everything because dryer was in tight space, little working space. Turned gas on, plugged in electric cord. Worked great now.

removed front cover, lifted drum up with a clamp and replaced slides. Replaced front cover

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

Unplug dryer

Pick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.

After you clean o ... Read more ut any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.

The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.

The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.

From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, t ... Read more he belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

Real easy I have resurrected my dryer may times so this was easy to replace the belt and idler pulley

Hinged open the top of the dryer. While dryer was running I tapped on the thermostat. The heater came back on. This verified the problem. Unplugged the thermostat, unscrewed it and replaced it.

I opened the top then i did change the heater element kit only one screw out and finaly replace the temperature switch, again one screw out was realy ease was my first time,the professional online help my, every one can do it thanks i appreciate your help.H.E.K.P/N AH2162280 - temp/switch p/n 31001449.