ADE20L2W Admiral Dryer - Instructions

I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wednesday

I was about to purchase a new dryer because of the age of my dryer and not wanting to hire someone to fix it. After a little web research, I saw several do-it -yourself stories indicating this was a very easy repair.

This was an extremely easy repair and it save me lots of $$:
(1) Disconnected power
(2) Opened the ... Read more top of the dryer
(3) Disconnected wires to temperature sensor.
(4) Used a 1/2" socket wrench with extension and a drill to remove 2 screws holding down the temperature sensor
(5) Removed 1 screw holding down the heating element.
(6) Removed wires connected to heating element and pulled out old element.
(7) Reassembled new element.
(8) Turned on empty dryer for 30 minutes to burn off smell from the new element.

Worked like a charm!

First went and got a beer.
Looked at the dryer.
Drank my beer.
Went and got one more, due to long job.
Looked at dryer again.
Opened the door.
Had to get one more beer.
Removed filter.
Got one more cold one.
Put new filter in.
Got one more beer.
Closed door.
Finished!

The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in.

I opened the dryer from the front by pushing in on the two clips just under the top. I then had to remove two screws on each side and took the front panel off. I reached around underneath on the right side to slip the belt off the pulley. I pulled the drum out and then I could see the roller that was squeaking (the left one). The whee ... Read more l had sheared some of the support off and that was the cause of the squeak.

I took the locking ring off and removed the wheel and support. I put the new support in, attached it, and then the wheel, washer and lock ring. I used pliers to push the lock ring onto the support.

Then I put the drum back in making sure it was in all the way (it fits snugly between the wheel and the back of the dryer). The belt is a little tricky to get back on. I put it around the drum and then reached underneath and behind again. The pulley is on a spring, so you have to pull it up and put the belt on all one-handed and blind. Once that was on, I gave it a few turns to make sure everything was working again.

It is quiet as can be now!

I slid in the new one

Parts Select made it extremely easy to order parts from their site. Parts came in a timely manner and very reasonable priced. Thanks to Parts Select! Door Seal just needed to be removed and replaced by pushing into little slot openings.

Unplugged unit, lifted the top cover, removed heater element screw, lifted out element, lifted out thermal fuse bracket. Removed wires from thermal fuse, confirmed was open curcuit at room temperature. Attached wires to thermal fuse, inserted fuse into bracket, slid bracket onto clip on side of box that housed the heater element, reinst ... Read more alled heater elememt, inserted long screw into heater element hole and tightened snugly. Extra to ensure proper air flow: Then removed wires from door switch on fron panel (labeled them), removed 2 screws at top of from panel, tilted and lifted front panel off, removed blower cover, cleaned all duct work from blower to exit of unit, sealed plastic duct that was attached to front panel. It had loose gaskets that allowed air to be drawn in from the sides and not through the duct thus bypassing the drum and heater element. Reattached blower cover, lowered and tilted front cover into place, reattached top 2 corner screws, reattached switch wires, lowered top. Plugged in and tested.
Note the Partselect sales person told me that the LA-1053 kit contained 3 items, however, it only came with the fuse, not the thermostats. Foutunately, only my fuse was shot.

It was easy - I had my 12yr old daughter do it. The old door seal was completely removed, then you placed the new seal in the apropriate knoches that are on the door of the dryer. The lint filter just had to be placed in the vent. - Done.

First I removed the two screws that hold the element in place. I then pulled the element completely out and disconnected the two wires.

From there it was just a matter of installing the new part.

Anybody could do it

Turn the power off to the dryer. Pushed the two retaining clips that held the top of the dryer to the dryer sides. One on each side of the front. Table knife works really well to do this. Lift the top of the dryer up all the way. You will see the heating elements in the rear center of the dryer. There will be one screw holding the h ... Read more eating elements in place. Once you remove the wires from the heating element and remove the screw the heating element will lift out. Remove the heating elements and set down somewhere they will not get damaged. On the side the screw came out of there will be the heat fuse (as Maytag calls it). Remove the retainer by picking straight up on the retainer and the fuse will come out with the retainer. Remove the wires and replace the fuse and reinstall in reverse order.

1. Removed wires to switch
2. Lifted top panel of Dryer with a screw driver
3. removed two inside screws holding the from panel against the drum.
4. Dropped front panel on the floor and removed door switch.
5. While the door was out, I removed the lint panel attached to the door - two screws.
6. Cleaned the door p ... Read more anel with a vaccum cleaner
7. replaced lint panel onto door with two screws
8. replaced door switch to the front panel
9. placed front panel on to the from of dryer with two screws.
10. Connected wires onto the door switch.
11. Closed top dryer panel and them pressed hard to catch on to metal clips.
12. Attached Dryer cable to electrical outlet
13. Trurned Dryer on and open door as it tumbled to confirm it would stop.
14. Done

Opened top of dryer and found high limit thermostat burned in half. Thermostat is located on top of element. Replacement of thermostat took less than 10 minutes, using phillips head screwdriver.

I first unplugged the unit, unlatched the top cover, removed the wires for the door switch, then removed the two screws securing the front panel. I "propped open" the top lid with a 2 by 4. I then lifted away the front panel, removed the blower housing screws to expose the blower. Then I removed the snap ring on the blower shaft, the c ... Read more lamp holding the blower wheel in place, and slid the blower wheel off the motor shaft. Reassembly was in the reverse order. Was very easy.

Opened the top by popping the two fasteners holding it down. Did this with a screw driver. Took two screws out of the front holding collector in place and two screws out holding the front to the two other sides. Put front of dryer down on the floor. Removed old collector and used all other existing material from old collector to fin ... Read more ish job. Wife could not believe how quick this was. Put back together was a snap too.