ADE20L1A Admiral Dryer - Instructions

Removed 3 screws and replaced the element and thermostate. No high priced repairman needed.Thanks

first I watch the video of the repair on the web site-(and for a guy like me who can not fix this was very very easy.Thank You parts select I will use you in the future. DON W.

Remove and replace thermal fuse.

Followed the instructions in the video and it was SO easy! Now my dryer works great!

This repair was so easy. All you need is a 1/4 inch nut driver or straight socket, a pair of needle nose pliers & a flat screwdriver,file or anything flat to pop the top of the dryer open. There are 4 wires to remove and 4 nuts. take the old parts out and replace with the new and replace the wires. Hardest part for me was making sure I di ... Read more dn't drop the nuts.I recommend watching the video. My dryer is working great.

I watched your video and it was exactly like you guys said. You truly have a great site and I will tell all my friends about it. Great service, can't say enough about how pleased I am with your site and service. Saved me a lot of money.

I watched a part select youtube video on possible fixes for the problem I was having. Ten minutes and two videos later I had the part out and identified as the problem. I ordered the part ($42.00) which arrived four days later. Spent ten minutes replacing it in machine, turned dryer on and went right back to performing the way it has for ... Read more the last 12 years. Easiest thing I did all day. Saved me $400 bucks too. Thank you.

Took less than five minutes to fix a couple screws and take some wires off and pull it right out. Called local apliance store if they had part wanted more than partselect with next day shipping

Unplug the dryer. Take a large flat head screwdriver and pop the hood loose from the retaining brackets on the front of the dryer and raise.Next, unhook the wiring from the thermostat and heating element with needle nosed pliers located in the back left corner. Use a 5mm socket to remove the thermostat bracket and the heating element brac ... Read more ket.Remove faulty part and replace. Replace heating element and tighten.Replace thermostat on the retaining bracket and tighten. Plug your wires back in and close the hood.Plug Dryer back in.

just like the training video showed, and was very happy at how it came fast, installed easy and back in the drying business.

It wasnt to bad,its way easy for people with small hands its a tight fit for larger hands that was my only problem.After putting the dryer back in service it still did not heat correctly so I pulled the lint catcher out and the vent hose off the back and blew it out with an air compressor my God what a mess it was plugged bad should have ... Read more had a fire so please look at doing the same with yours if its an older dryer.

1st replaced the broken drum belt, then the heating element failed, ordered a replacement, arrived over night thank you very much. Installed new heating element, 5 minutes later the motor failed. Bought a new dryer, ate the heater element as it is now used.

I drilled two holers in the side of the cabinet 1 inch apart. I put them at the same height as the tensioner spring. I put the string through 1 hole and around the tensioner. I pulled the string through the other hole and had my son hold the tensioner back while I reached in and lined up the belt on the tensioner while my son let out the ... Read more string slowly.

Basically I started off using youtube to see how to install. Two things to be sure you do – one the plastic washer only goes on one side (read the instructions)of the shaft and two the support brackets are not threaded so you need to use the original self-tapping screws. The screws that come with it will not work. Best to use a socket ... Read more set to install the screws.

Disconnected dryer main power supply from wall socket. Opened dryer top,Thermal Fuse is mounted on the Heating Element support bracket on the upper left hand side of the back wall of the dryer. Disconnected wires from damaged Thermal Fuse. Removed hex bolt securing Thermal Fuse Bracket with a nut driver for easier access. Pull up on Ther ... Read more mal Fuse support bracket and remove. When reinstalling Thermal Fuse bracket be sure and line up securing clips with the slots on the Heating Element bracket. Once these are alinged push down until Thermal Fuse Bracket is secure and proceed installing the hex bolt to finish installation. Reconnect both wires and dryer should be ready for operation.