ADB2500AWS2 Amana Dishwasher - Instructions

I had to force the door open, due to a broken handle/latch.
Ordered assembly with help of order desk to assure correct part number. Arrived within 3 to 4 days. Not sure but very fast. Only had to wash dishes by hand once.
Turned off power to dishwasher, my electrical panel is clearly marked with switch for dishwasher. No guess ... Read more work there.
3 min. to remove old assy. 3 min. to replace with new part.
I might add that I am a 67yr. old female. So if I can handle this repair, anyone can.
Saved repairman service call, or purchasing a new dishwasher.

Most of the time was spent pulling out the dishwasher from under the counter, as a new tile floor had been installed after the DW was installed.

Great pictures of components on this website confirmed what part to order.

Shut off water feed to DW and disconnect power to DW.

Unplug wire connector to old ... Read more valve (solenoid) and disconnect water inlet hose. Observe that valve is attached to sheet metal bracket.

Remove bracket, with valve attached. Don't remove valve from bracket. New valve comes with sheet metal bracket.

Remove female threaded adaptor (brass) from back of old valve and screw on to new valve using Teflon tape. That is the only piece you need to reuse.

Attached the new bracket (with valve attached) to DW. Attach water inlet hose. Attach plug to new valve.

Turn on water to DW. Check for leaks. Retighten hose connection if required. Run dishwasher. Keep lower panel off for a couple of days to be certain no leaks develop.

Removed the screws on the door of the dishwasher, lifted up inside of door to get to the latch assembly, unplugged the 2 sets of wires, removed the old broken latch. To install new latch did all of the above in opposite order.
Very simple, quick easy fix. The only thing that might be an issue for some people is that you need a set o ... Read more r torx head screw drivers. (nice little set at Home Depot for less than $10. I'd say.)

I ordered and replaced both the door gasket (easy) and inner door seal (difficult) to try and correct a leak during operation. The door gasket was easily replaced. However, the inner door seal was a bit more trouble. After removing the inner door I found that the old inner seal needed to be removed and surfaces thoroughly cleaned of old ... Read more build-up of dishwasher soap residue, in order to allow the sticky back tape side of door seal to properly stick to the door. There also was a plastic cover over the wire bundle that needed to be cleaned. The inner door seal was the exact length, so proper positioning of the sticky back was very important.
Upon reassemly the leak still existed and I was unable to correct the leak. Further inspection indicated that the basic tub/body of the dishwasher might be slightly distorted due to age and may not create seal with door seal as originally designed.
I guess I need to find a new dishwasher, at this point.
A word to the wise: Check to see if the tub/body is still in good condition.

Easy to do. Order the handle (with latch assembly) rather than the latch assembly. It's cheaper and it contains both parts (handle and latch). Turn off the power. Use a T20 star tool to remove the screws inside the door. The latch assembly will fall right out as it uses the screws holding on the door. The hardest part is getting enough ... Read more nerve to pull the two electrical plugs out. They are really tight and need some pulling with pliers. You might want to put a dot on the wire connector with a sharpie so you can put it back in the right side up. Connect the wires to the new assembly, place in door, put screws back in. Turn on the power. Done. I called a repair place and asked for a estimate for this job: $150-200 with parts. I did it in 10 minutes for $30 worth of parts.

I had to remove the 4 screws holding the toe panel. Then I had to take out the one screw holding the floater switch housing in place. It snapped open to release the floater and that just lifted out. I put the new float in and snapped the new housing on. I put the screw back in to hold the housing in place attached the two wires to the swi ... Read more tch and put the toe panel back on. It was all very easy to do and my first home repair went very well. thank you.

After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back ... Read more in operation. Hans.

the new dishrack fit right in immediately with no tools needed. Delivery was prompt

Having read some of the other stories on this site, and not really sure what subpart was ACTUALLY broken, I ordered the latch assembly rather than the latch - and as another user mentioned, it's actually cheaper. I

Installation was an absolute breeze - the drill/driver is just added hedonism - but if you are going to use one, ... Read more make sure it has a variable clutch so that you can put it on one fo the loosest settings to avoid stripping the screws.

I open the dishwasher door and held it open with a heavy pot and removed the screws (about 14) around the edge of the inside panel in the door.
The panel lifts way easily (if you remove the pot). The panel is attached to the latch assembly by two wiring harnesses - make note of which goes to which, they ARE IDENTICAL and you will not be able to tell them apart later.
I just lifted the broken assembly out, and fished out the other shards
Next, after repeated attempts to remove the harness from the switches in the assembly and failing, I just swapped the old switches still attached to the harness into the new assembly.
Place the assembly back in its slot, the panel fits back on fairly easily, drive the screws back in without stripping, and enjoy the silky feeling of a latch that shuts again
Enjoy beer

I pulled the unit from under the counter. the springs and cables are on the front sides of the dishwasher. I moved the insulation removed the broken spring and cables and replaced them with the new parts. just one side was broken, but I replaced both while I had the unit out.

The initial repair was more involved due to figuring out how to get at the problem. A foam sealer strip located at the bottom of the inner door had lost it's seal. I first sent off for one and it was of relatively thin material. It was carefully installed but still leaked. I ordered another one from Part Select and it had thicker foam. It ... Read more was installed right over the previously installed strip and made a tight seal. (knock on wood)

Removed plastic lining from dishwasher door with torx screwdriver, then removed screw holding door latch assembly in place. Removed existing switch from door latch assembly and replaced.

This switch was not the correct one initially as it was a normally closed switch, whereas the existing switch was a normally open. Was able ... Read more to pry open the switch and switch the contacts to normally open so it worked out in the end. Would recommend purchasing the complete latch assembly w/ switches if you aren't comfortable taking the switch apart.

I removed the screws, and unplugged the old part, plugged in the new part and screwed it back in. It was so easy it took about 10 minutes. I surprised my husband when he came home to repair it, it was finished by me!!

took the bottom spray arm & lower plastic pieces out, unscrewed the impeller & replaced it. the original impeller which holds the disposal blade down & wore down & no longer retained the blade. snap.

Replaced the door seal. Removed the old seal and gently stretched the new seal and pushed it into the channel. Snipped off about 2 inches excess seal. As far as the Inner Door Foam Insulation Strip goes, it was not as easy. To begin with, the old Foam Strip was attached to the door insulation and not the door. The attempt to remove t ... Read more he old Foam Strip from the insulation became cumbersome, so I just attached the new Foam Strip on top of the old Foam Strip. So far, after a few cycles, it appears that it corrected the leak.