ADB1500AWZ Amana Dishwasher - Instructions

After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The o ... Read more nly problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

All that was broken on the old detergent dispenser was the door but the door can not be ordered without buying the whole detergent/rinse aid assembly. When I got the new item I just removed the old door and replaced it with the new door that I had taken off the new one. I still have the new detergent/rinse aid assembly that I can keep if ... Read more I need to change it in the future.

The repair was as easy as 1, 2, 3.. 1) Open box that the new dishrack was shipped in from PartSelect. 2) Take old and dry rotted dishrack out of my dishwasher. 3) Place new dishrack into my dishwasher.

Less than 5 minutes.

After examining the door and main seal around the dishwasher I thought everything looked okay. I looked online to order a new seal anyway and discovered from others that the leak was probably the insulation strip inside the door rather than the seal around the dishwasher. I ordered an insulation strip and it arrived a couple days later. ... Read more I removed the seven screws of the interior door cover and disconnected the electrical. After removing the old insulation strip and installig the new one I reconnected the electrical wiring/plugs, put the door cover back on, and reinstalled the screws. Total time was about 15-20 minutes and the leak stopped. It was very easy and saved the cost of a repairman or a new dishwasher. I'm very glad that I "listened" to others and went with the new insulation strip.

removed the cover to remove the door seal then replaced it with the new one and replaced the insulation strip

Unfortunatly if the plasic handle breaks you will need to purchase the handle/latch assy. However it comes complete with the interlock switches so it made the repair quite simple. . . Removal of the inner door panel also releases the handle/latch assy. Unplug the interlock sws. And install the new hanle/latch assy. While putting the i ... Read more nner door panel back in place. . . Clean up the mess you made and it's done. . . 1/2 To 3/4 of an hour and part of that is rounding up the tools you. . .

First shut circuit breaker to dishwasher and close water valve under the sink. Remove the screws that hold the dishwasher to the counter, then remove the bottom cover plates. I slid the diswasher out almost all the way...On the left side bottom I could see the old water inlet valve was attached by 2 hex screws and a clip with 3 wires..aft ... Read more er removing the 2 screws and clip I was able to remove the water line (place something to catch a small amount of water) and remove the black rubber hose from the old intake valve by squeezing the clip.. Removed the brass nut from the old valve you'll need it. I installed the new water inlet valve by connecting the old brass nut
(replace with new thread seal tape) , replace the water line and black rubber hose...attach to frame with the 2 hex screws and replace clip with wires...I slid the dishwasher back under the counter, turned the water on and power back on...I ran the dishwasher before I secured it in place to check for leaks...Dry as a bone...I then secured it to the counter and replaced the bottom plates.. the dishwasher is working like new...everything comes out spotless...Sometimes repairs are not as hard as they look, just take your time.

First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into posit ... Read more ion. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

There was a tear in the fine filter (fabric) on the accumulator. This can be seen by looking in dishwasher without having to disassemble anything. Food was being sucked in and sprayed back out on dishes.

Disassembled, cleaned, replaced part then reassembled.

Cleaned out the spinning sprayers -- used toothpicks t ... Read more o clean out holes, flushed with water.

Cleaned out under the accumulator.

Works like new.

1). Unplug Appliance
2). Open Door of Appliance all the way.
3). Remove screws around inside edge of door but do not
remove inside panel. Leave it lay there on the door.
4). Slightly seperate inside face of door at the top of
the door inside enough to access the plug-in latch
unit.
... Read more >5). Unplug 2 plugs on electric latch and remove broken
latch. (Screws around inside door panel held latch)
6). Substitute New Latch For Old Latch
7). Plug in 2 plugs on new latch and put latch in place
8). Replace screws around inside edge of door
9). Close Door and Re-open to ensure that new latch works
10). Plug In Appliance

Remove the 4 screws at the lower panel, turn power off to dishwasher, remove single 1/4 attaching screw from float switch, open the door remove the old float assembly. Make sure you install the float in the machine first than side the switch over the end of the float before screwing it back in.

first i removed the back of the dish washer door and determined the handle was broke.went online with you with model number and looked at the parts breakdown. ordered the latch assy,however the latch assy i ordered did not come with the handle,reordered handle and got latch assy and handle and it was cheaper--go figure! you guys were grea ... Read more t! received ra# for part to return asap and i'am very pleased! thankyou for your great service! i will tell others about your service! again thanks!

Not a bad repair once you diagnose the problem. Took me three tries to figure it out. Just make sure you follow the instructions. I used an allen wrench to hold the motor in place while tightening the part onto the motor shaft, this way I didn't have to remove and flip the dishwasher to do the repair. The good news is the replacement part ... Read more I needed was metal instead of plastic, thus I should never have this problem again. I don't understand why it was plastic in the first place but all of my appliance problems seem to be made to fail after several years of service.
Repair was

I turned off the electricity at the circuit breaker. Sitting in a chair in front of the opened dishwasher with the partially opened door resting on my knees, I removed the 10 screws lining the inside of the door (setting them in order on the cabinet above -- 2 are different length so this helps keep them in order.
I tilted the inner ... Read more cover on the door up (which is what the screws had been holding). With the door not fully open because it was on my knees, I was able to position the cover so that I did not have to remove the connection to the soap dispenser.
The two middle screws removed earlier were the screws that held the latch in place, so the assembly was already loose at this point. I put a black mark on the assembly to mark the side that the black wires were attached. Then with the pliers removed the plugs that were connected to the switches on either side of the assembly. Then marked the replacement assembly with the black mark on the same side as the one removed. I attached the plugs to the the replacement assembly using the black mark as reminder for which side was which.
I lined up the latch on the door where it goes, lowered the lid (lifting the lower edge over the base a little), lined up and started the latch screws (middle 2), then started all of the other screws and then tightened them all. Closed the lid and tested the latch. It was closing correctly now. I turned on the electricity and tested to make sure all was now working properly.

First I opened the breaker on the dishwasher removing power from the unit. Then I removed the Torx head screws on the cover on the back side of the front door. Then I pulled off the stainless steel sheet metal panel which exposed the door latch. Then I unplugged the electrical connectors to the two micro switches on the assembly, next ... Read more I plugged in the connectors on the new latch assembly and postioned the latch back on the mounting holes. Replaced the stainless steel sheet metal and put the screws back.