ADB1400AM Amana Dishwasher - Instructions

Removed old part and replaced with new part

Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.

I removed the lower front panel of the dishwasher to expose wheels and opened door and removed two screws holding washer to cabinet. After raising leveling feet pulled washer out to expose bnotton ow dishwasher. Removed the electrical wires form the heating element and removed screw caps holding the heaqting element in place. Removed the ... Read more old element and inserted the new, then reversed process to get it back together. It was very easy to do following the instructions I received when I ordered the part.

Turned off power to the dishwasher. Removed the front panel via the screws on the inner wall of the door. Lifted and pulled out the front panel. Disconnected cable connections to fully remove the front panel. Pressed down on the latches to the left and right side of the door latch. Pulled out the door latch. Put in new door latch until it ... Read more clicked into place. Reattached cable connections. Put the front panel back on with the screws. Turned back on power to the dishwasher.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Did the repair, but needed one extra step not described in video:

I followed the directions on the PartSelect Youtube video - very helpful! I do believe the heating element was the original culprit, as it had a "burn" area about the size of a dime that caused it to almost break into two parts. Obviously a point of failure.
... Read more >
BUT - after replacement, it still did not solve the problem of the dishes not drying.

After much web searching, I tried the diagnostic mode on the dishwasher, and that did a hard reset of the logic board and FIXED the problem.

So in all, it required both a new heating element AND a hard reset via diagnostic mode.

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and ... Read more install new switch and reconnect the wires.

Something had been loaded in the dishwasher that had gone thru the basket - it hit the arm sprayer and broke it off.

Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.

I watched a you tube video whic ... Read more h was referred by part select. This was helpful.

I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..

It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then t ... Read more ry and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

After replacing the door seal and the dishwasher still leaked a lot of water out the bottom of the door, I read posts by a couple of other DIY who said the lower spray arm can split at the seam and cause this. One post noted it is very difficult to determine if this is the problem, that you may have to take the blade of a screwdriver and ... Read more try to pry the seam apart gently to see if a gap does appear with very little force being applied. If so, then just imagine what happens when that very hot water makes that plastic more flexible and then the seam opens and forces waves of water against the lower door. I could see a small seam split using that strategy and when I replaced the spray arm, my leak stopped. I don't regret replacing the door seal as it had a couple of small tears and hard water deposits all over it, so it was time to do that even though it was not the culprit for the extensive leak. The arm is SO EASY to replace, just twist the plastic nut under it and it pops right off. Put the new one on and twist the nut the other way and it secures it.

Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.

Snap in the missing track stop and twist snap the middle spray arm. That simple.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. ... Read more Checked for leaks. Good to go!

quick and easy replacement, without tools...

i ordered the wrong part and received the new part and credit for the old part, quickly...Plus, I was kept informed with e-mails....

excellent service...