ADB13 Amana Dishwasher - Instructions

New one snapped right into place.

I used a flat blade screwdriver to compress one arm of the endcap of the slide rail to free it. I then slid up the locking slide of the old roller assembly freeing it from the upper basket,and put the new part in its place. I then put the roller back in the slide rail and replaced the endcap.

Followed very simple instructions to easily install. The only tool needed was a flathead scredriver to pop off caps to remove old, broken rollers. New rollers simply click into place. Piease aren't cheap, but significantly less than a new dishwasher.

Unscrew top filter, pry off bottom filter, replace with two new filters

Pulled out old gasket, pressed in new starting middle top. No more leak.

TOOK OFF RACK ROLLERS ON OLD TOP RACK AND BOTTOM RACKS ALONG WITH TOP WASH SPRAYER AND PARTS AND PUT ON NEW BASKETS.
PIECE OF CAKE!

My dishwasher wasn't completing cycles and would start to smell like burning plastic randomly. I determined it wasn't coming from inside the tub but underneath the unit. I replaced the drain pump and the drain hose as a precaution to make sure the check valve inside wasn't getting stuck closed forcing the pump to not be able to drain. It ... Read more was a very easy repair that just involved taking the dishwasher out of the cabinet and turning it on its side. The old pump just twists out and the new one goes in just as easy no tools required. The video instructions on the product page here were very helpful. The hose connects with a clamp and is routed on the side with some plastic clips. It was very easy and completely solved the problem!

Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb

I just snapped the old one off and snapped the new one on..

Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!

Pulled dishwasher out unplug the wire on each side unscrew the nut on each side lift up in the back of element pull it out on metal holder for element and put the new one in really easy thanks so much for the help!!

I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed ... Read more I had done it right.

based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I did ... Read more n’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.

Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.

The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a ... Read more hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.