ADB12 Amana Dishwasher - Instructions

Latch assembly came in a matter of days. Screwed it in and voila! good as new.

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three s ... Read more crews holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

I first listened carefully and noticed that during cycling, the electric motors could be heard starting, stopping, and apparently running normally during both wash and emptying cycles. However, no water was being pumped around during the wash cycles, while emptying (which uses a different motor) worked normally throughout all cycles. Th ... Read more us it seemed to me that the electronic programming was working correctly in turning both motors on and off as necessary. So I figured somehow the wash motor impella was not turning and pumping water, despite the fact that the motor was indeed running correctly. So I removed all the plastic housings, the screwed on impella, and the metal chopper at the base of dishwasher. Then I was able to easily pry the old plastic chopper sleeve right off of the electric motor shaft (normally it is screwed on and cannot be pryed off). Since the plastic threads inside the chopper sleeve were completely stripped, the motor shaft would turn but the impella would slip on the shaft and not be driven. The replacement sleeve was much better constructed (metal not plastic). It could be easily screwed on to the motor's driveshaft after lifting the old rubber seal and gently holding the motor shaft with a pliers (carefull to avoid scratching the shaft). I removed the old rubber seal nd replaced it with the new one from the kit, right over the newly installed metal chopper sleeve. Next, I easily centered the metal chopper sleeve and pressed in the new seal after reinstalling the plastic/metal chopper screen, using the temporary jig included in the kit. Then the jig was discarded and the impella simply screwed onto the chopper sleeve (using the appropriately threaded hold-down screw provided in the kit). Finally, the rest of the plastic hardware is screwed in place. Waahhlaa...now impella is motor driven again and blows water hard into the dishwasher during the wash and rinse cycles. Total cost of job to do-it-yourself, $29.50 including shipping (which only took three working days). Estimated job if down by appliance repairman, $140 (assuming the repairman didn't first erroneously blame the problem on faulty electronics then charge you hundreds of $$'s to replace circuits which were not broken to begin with, only to find the dishwasher still not washing/rinsing after his expensive electronic circuit replacements. The actually mechanical fix was cheap and simple. Truthfully, there is no excuse for Jenn Aire to ever use a plastic Chopper Sleeve in their dishwashers to begin with.......carefully planned obsolesence if you ask me. Oh well, it works perfect now. I doubt if even the four marbles my 4 year old had tried earlier to wash in my dishwasher (stripping out the original chopper sleeve) would do any damage to the metal replacement. However, I don't plan on testing my hunch. A simple fix, but a slightly challenging diagnosis which relied on a keen sense of hearing and a quiet workplace. Seems many people in these blogs have had the very same problem with their Jenn Air/Maytag dishwashers, and have made the same diagnosis and the same simple fix. Thank you mucho, PartSelect.

Shut off power to dishwasher, remove screws holding panel to door , move panel enough to get to circuit board. Remove three nut drivers screws, unplug cables from circuit board. Remove circuit board by unsnapping from side ears, replace new circuit board, plug in cables. secure with screws, secure door panel. put power back to dishwasher.

In less than 5 minutes we took the screws out, fixed the latch and had it back together again. The amazing part of the story is the perfect diagrams and helpful instructions from Part Select. I ordered the part one day and by noon the next day the dishwasher was fixed!

Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish ... Read more the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

The original piece is 100% plastic (with metal shields only to prevent burning). The bushing of the arm was badly worn out in one side. The arm was no turning properly or at the end no turning at all. I decide to drill the new part in order to fit a brass bushing inside (1/4" ID, 5/16" OD, about 2" long). I expect it will last conside ... Read more rable longer. I would say this is a typical "defective by design" problem.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new pa ... Read more rt in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

Switch was not the same switch as what was in the unit, similar but switch was normally closed instead of open, so had to take the switch apart and change sides with the contacts! should be the same, but was not, so in the end worked fine after an adjustment!

Wanted to change our dishwasher to a stainless steel appearance. When the panel was delivered in 1 day I might add it was flawless. I removed the old panel and the new panel attached to the dishwasher perfectly with the screw holes exactly lining up. The most inexpensive way to turn a kitchen into a stainless steel appliance look.

Simply unscrewed the door and plugged in the new parts. Very quick, very easy, saved us hundreds on a new dishwasher.

First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a lo ... Read more ss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.