ACX100 (P1133389N) Amana Cooktop - Instructions

Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...

lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly

One screw taken out, 2 wires switched, new part & screw put in. Burner like new!

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be su ... Read more re and disconnect power before starting!!

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so yo ... Read more u have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You

ulplugged elements and dropped in new pans

Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!

Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.

burner was shorting out replaced part works great

loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.

It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.

The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase.. ... Read more .parts arrived very timely...J. Iriwn

I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new b ... Read more racket and installed the burner. double checked everything and lowered the top. Done

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.