ACS3 - Instructions

Researched through this site to find part numbers and names. Youtubed it to see how to install the part. Ordered the exact part via this site and received it in only a day or two. Installed it in less than 15 minutes and the oven works amazing. It gets up to temp quickly and holds temp better than it has in years. Very satisfied!

Removed the three screws holding the igniter, pulled the old one out and plugged in the new one. Very simple.

Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that yo ... Read more u unplug the appliance !!!!

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

It was really easy because I read information on your site. I only had to unscrew 3 screws, remove the old spark ignition electrode, replace the new one and then screw the 3 screws back. It was great

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predri ... Read more lled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

1. Remove sliding shelves and lower pan sheild
2. Remove flame deflector
3 . Remove the 3 screws that hold the igniter in place. Insert the new cable and plug through the opening for connection in step 6. You may hve access to connector. If so skip to step 8.
4. Remove sliding storage drawer
5. Remove the sheetmetal pa ... Read more n to gain access to the igniter connector. It might help to have several blocks of wood the elevate the frront of the stove to allow more working clearance.
6. Disconnect old igniter, connect new igniter.
7. Replace pan and sliding drawer.
8. Remove old igniter from carrier and install new one.
9. Install igniter carrier to stove with 3 screws
10. Replace flame deflector and lower pan sheild.

The repair actually started online trying to figure out the problem. The parts list and picture provided were a big help. I actually got lucky when I ordered the part. It was a little difficult to get to but once I got the old one out, it was easy and done quick. Saving at least $100 on a repair man was awesome. I had to find the pa ... Read more rt in the stove first. Then had to find the wiring harness to disconnect. After taking off the back panel and the oven burner plate, the wire harness was exposed. I disconnected, taped on the new wires, remounted the new igniter and put it all back together. Pretty quick and pretty easy.

It took me a while to figure out how to access the igniter (I ended up removing the drawer and had to slide underneath the oven.) Once I removed the two sheet metal panels, I unplugged the old igniter and plugged in the new one. Installing the igniter inside the oven was easy--three sheet metal screws that hold the protective cover.

remove oven flare pan in bottom of stove, about 25 screws, lift out and remove igniter. tip stove back and remove splash pan from underneath, 2 screws, unplug ignitor and reinstall using reverse procedure. igniter is very fragile so be extremely careful with it. reuse old hardware to hold in place,reassemble and good to go.

Baking ignitor glows but gas valve not opening. Replacing the bake ignitor solves the problem.

Here is how to do:
1) open the oven door, unload the racks, bottom plate, and flame deflector. unscrew three screws (phillips screw driver needed) to loosen the bake ignitor (along with the metal rack).
2) take out the bott ... Read more om drawer. you should see two screw all the way at the back. unscrew them to take off a metal cover. you should see the connector. unplug to take off the defective ignitor.
3) plug in the ignitor and put everything back in reverse order.

It took me a while to figure out how to access the connector at the bottom back of the stove. The next time it should take less than 15 minutes.

All I would like to say is that I am very satisfied with the service I received from PartSelect.

I definitely would order from them again. By doing the work myself, I believe I saved $80 in labor costs.

Thank you

1. Disconnect oven electric supply.
2. Remove oven door (2 screws).
3. Remove inside-oven bottom plate (slide forward, lift).
4. Remove inside-oven burner cover (1 nut).
5. Disconnect igniter enclosure (3 screws).
6. Remove under-oven drawer (slides out).
7. Remove panel at back of oven in under-oven compartm ... Read more ent to access igniter electrical connection (2 screws).
8. Disconnect old igniter.
9. Extract old igniter from igniter enclosure. (Don't use much force; just slightly expand the metal flanges of the enclosure.)
10. Dispose of old (bad) igniter.
11. Insert new igniter into igniter enclosure.
12. Place igniter enclosure in oven compartment and slide electrical connector through to back/lower compartment.
13. Connect new igniter in under-oven compartment.
14. Replace panel at back of oven in under-oven compartment (2 screws).
15. Replace igniter enclosure (3 screws).
16. Replace inside-oven burner cover (1 nut).
17. Replace inside-oven lower plate.
18. Replace oven door (1 screws).
19. Reconnect electric supply.

First I removed the two screws that hold the element in plance. I then pulled the element out about 3 in ches and disconnected the two wires

I listened to see if the stove was igniting. It was not so we went with the igniter. It arrived in three days. I thin watched a u-tube repair. It was very helpful but looked as if a few steps were unnecessary. After reading the responses decided what steps could be eliminated and carefully replaced the part. It worked the first time. ... Read more Besides handling the ceramic part very carefully the hardest part was remembering what screws went where! Extremely glad I took this on as a first time stove repair.