Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Element wasn't being controlled by the switch it would stay on high
6 of 7 peoplefound this instruction helpful.
George from FRANKLIN, KY
Very Easy
15 - 30 mins
Screw drivers
Ordered a new switch and replaced the old one with it.
Was this helpful?
Thank you for voting!
The 8-inch burner only heated on high regardless of the temperature setting dialed in.
6 of 7 peoplefound this instruction helpful.
Reginald from PLAINFIELD, IN
Very Easy
15 - 30 mins
Screw drivers
Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to
... Read morenew switch. Screwed replacement switch back onto stove. Reattached back panel with screws.
Read less
Was this helpful?
Thank you for voting!
Stove burner wouldn't heat
6 of 7 peoplefound this instruction helpful.
DAICHI from Louisville, KY
Really Easy
15 - 30 mins
Screw drivers
First I disconnected the power, removed the screw that hold the element in place. Then, I pulled the element out and cut the two wires. I connected the two wires with the new element as the instruction provided by Part Select. I put the element back and screwed it in place. I plugged in the power and turned on the burner. It works. It is
... Read morereally easy to repair.
Read less
Was this helpful?
Thank you for voting!
electric coils would not stay flat as drip pans were incorrect fit
Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 peoplefound this instruction helpful.
Carl from RIVERSIDE, CA
Very Difficult
More than 2 hours
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
The heating coil was no longer working.
5 of 6 peoplefound this instruction helpful.
Amanda from Midwest City, OK
Really Easy
15 - 30 mins
Screw drivers
My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling th
... Read moree oven out to get behind it and sliding it back in.
Read less
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 peoplefound this instruction helpful.
Sharon from Yacolt, WA
Really Easy
Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartri
... Read moredge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.
Read less
Was this helpful?
Thank you for voting!
two large burners wouldn't heat or would smoke even after cleaning
5 of 7 peoplefound this instruction helpful.
Lois from KNOXVILLE, TN
Really Easy
Less than 15 mins
i really wanted a new stove, but budget wouldn't permit; so just had to insert the new ones and they work great with level cooking.
Was this helpful?
Thank you for voting!
Generic drip bowls in the stores did not fit
4 of 4 peoplefound this instruction helpful.
Elaine from BROAD BROOK, CT
Really Easy
Less than 15 mins
Very easy remove the burner and instill the drip bowls
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this helpful?
Thank you for voting!
element went out on the stove
5 of 7 peoplefound this instruction helpful.
christopher from harrisburg, NC
Really Easy
15 - 30 mins
Screw drivers
My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's
My Orders
