This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are most often used to light the inside of refrigerators and ranges. It features a standard socket base, which means you simply unscrew the burnt-o...Read moreut bulb and screw in the replacement. Depending on the appliance you may require a screwdriver or nut driver to access the light bulb. We recommend you wear work gloves while handling this replacement part. It is constructed of glass and metal and is sold individually. Depending on the appliance and location of the bulb within it, you may want to consider disconnecting power and using a flashlight for easier access to unscrewing and re-screwing in your bulb during this repair.
Use this scraper for your ceramic/glass cooktop. It has a retractable blade and is an all-purpose tool for cooktops, mirrors, windows and tile. Use it to also remove paint, paper, dirt, stickers and more.
This surface element is made for under glass set-ups and supplies the heat to a cooking area on top of the range. It has an outside diameter of approximately 7 inches (1500 watts), and is a genuine OEM part sourced directly from the manufacturer. Before you replace your faulty element, make sure the element is cool, and the power is disconnected from your range.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Outer Heater ring not working on dual burner.
24 of 28 peoplefound this instruction helpful.
Mark from Richardson, TX
Really Easy
30 - 60 mins
Screw drivers
Turned off power to unit. Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws hol
... Read moreding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact. Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.
Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.
Read less
Was this helpful?
Thank you for voting!
Both fan and light switches were broken.
18 of 23 peoplefound this instruction helpful.
Peter from Media, PA
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers
TURN OFF POWER TO RANGE AT FUSE BOX -- a)Open the oven door, b) Unscrew the left and right silver nuts (not the black screws)that are in the oven under the control panel, c)pull off the four control knobs on the control panel, d) gently tilt out the control panel, e) set the control panel in/on the protruding arms, f) pull off THE connect
... Read moreors at the back of the switches - remember which is top and bottom, g) use a screw drive to break off the plastic pieces that hold the switches in place, h) push out the old switches, i) push/snap in the new switches, j) reconnect wires, replace control panel and screw in the nuts.
Read less
Was this helpful?
Thank you for voting!
The burner was not heating up
11 of 14 peoplefound this instruction helpful.
Jeffrey from Miami Lakes, FL
Really Easy
Less than 15 mins
Pliers, Screw drivers
I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together. I am sure that I saved at least $200 in "lab
... Read moreor".