ACF4205AT (PACF4205AT1) Amana Range - Instructions

First I unplugged the unit. I removed 4 screws to remove the back plate. Removed 4 screws to remove the ERC unit. ( Plastic casing and all) Peeled the front cover off the old unit and stuck it on the new. Removed one wire at a time and plugged it into the new so I didn't mess up the wiring. screwed my 8 screws back in, plugged it in, ... Read more and started cooking.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together.
I am sure that I saved at least $200 in "lab ... Read more or".

1. Flip "OFF" circuit breaker.
2. Pull out range unit from wall.
3. Unplug range unit.
4. On the back of the range unit, remove 4 screws holding lower rear cover using a phillips head screwdriver.
5. Remove lower rear cover.
6. Unplug temperature sensor connector (1 wire connector located upper right section behin ... Read more d oven).
7. From inside oven (upper left, back corner), remove 2 screws holding temperature sensor unit using a Phillips head screwdriver.
8. Remove old temperature sensor unit.
9. Insert new temperature sensor unit (wire connector end first) through opening and secure reusing old screws.
10. Re-connect temperature sensor connector.
11. Re-attach and secure lower rear cover reusing 4 old screws.
12. Plug in range unit.
13. Move range unit back to desired location.
14. Flip "ON" circuit breaker.

Purchased 2 piece broiler pan from this site

I just got on youtube, typed in "replacing hinges on an amana oven door" and an awesome video popped up. The job was a cinch.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

A Home Depot employee advised me on how to enter all my oven information found on the front of my oven on parts.com. I submitted parts information as stated, also very easy. My parts arrived 3 days later. I used a screwdriver & pliers, it took less than 15 minutes. Very simple and the entire process from order to installation went like cl ... Read more ockwork. I would definitely order in the future. Thank you.

The repair was easy. I removed the 4 screws to the upper rear cover in the back of oven then unscrewed the 4 screws holding the ERC, Elec Conv-Geneses and undid the 6 color wire conects and the 4 wire plugin. The color wires are labled on diagram and on part. Replaced the divice and reconnected it the same way it in reverse.

... Read more >However that was not the problem. There was nothing wrong with my ERC, ELEC CONV-GENESIS. I did not check the power to the circuit.
I just figured that it was getting power since the indicator lights were working. One of the 240 circuit
of the circuit breaker was bad (burned out). I turned off the main and replaced the circuit breaker. Works fine now. One learns by there mistakes. Hope this helps...
O by the way I thought I would keep the part just in case I might need it in the future as a backup.

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest ... Read more that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

my husband turned off the electric supply, pulled out the stove, took out a couple of screws, put the new part in, and the job was finished

Remove the 4 screws to the upper rear cover in the back of oven then unscrew the 4 screws holding the ERC, Elec Conv-Geneses and undo the 6 color wire conects and the 4 wire plugin. The color wires are labled on diagram and on part. Replaced the divice and reconnected it the same way it in reverse.

It may help to remove the scr ... Read more ews in the lower cover panels on the back of the oven to help reassembly.

removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy
Donald Carpenter

I took the back off the stove and four screws were removed to replace the old unit with the new one. Very easy. I also used the parts diagram from part select to find the part and order it. there follow up for shipping was great.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. ... Read more Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.