ABL2 Refrigerator - Instructions

The initial problem was that the ice maker was not working. I had the unit repaired at a local store and they assured me that it worked fine in their workshop. I believed that the valve was the next logical part to replace. The installation was very easy. I unplug the refrigerator and turned off the water. Removed two, easily reached, scr ... Read more ews and pulled the unit out. Disconnected the wire harness (you may want to mark the top of the wire harness before removing for immedite alignment on reassembly) and tubing. Notice a spot in the tubing that had been kinked, so cut that out. Reassemble and turned everything back on. Installation went perfectly. Unfortunately, I still do not have ice and will be doing some additional trouble shooting to determine the next course of action. I may be in touch.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

I removed the glass top and then rail and frame.
I had to remove the gaskets from the old frame and put them on the new one.
The steel support and the slide mechanisms were difficult to remove. I needed a screwdriver to do this.
Some directions would have helped here.
It was easier to snap them back into the new frame. ... Read more
I set the frame and then rail back into the refrigerator,
replaced the glass.

Turned old one until it snapped out. Replaced it with a turn.

Removed the drawers and shelf unit above the shelves. Installed the new rail and put the shelf unit and drawers back in. Less than 5 minute repair. Very fast delivery of part and reasonable pricing.

Turn water and refrigerator off, use hair to thaw the ice maker filler tube, then remove the filler tube inside the freezer. Next remove the water supply line cover plate in back of the refrigerator. Now remove the speed clip at the white pvc elbow and pull out the supply line. Next, grasp the pvc elbow with pliers and pull hard to rem ... Read more ove. The new filler tube is a 1 piece design (filler tube and elbow combined) and needs to be cut to the proper length. Mark it inside the freezer, remove it and cut to length. Now coat the outside flange with caulk or PU glue and snap into the opening. Put the speed clip on the elbow first and center it. Ensure that the spreader insert is in place in the plastic tube, then slide the supply line into the elbow untill completely engaged. Replace cover.

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

Pantry Cover:

I just slided out the tray, and unscrewed the left pantry panel that was broken, and replaced it with the new one, then put in the new cover after sliding the trays back in.

Ice Maker:

I unplugged the power connector in the back, unscrewed the ice maker with a flat screw driver (3 screws), s ... Read more lide it out, and then unplugged the wiring from the old ice maker and put it into the new one, mounted the new ice maker back in, make sure the lever is working, and then closed the freezer to let it cool down so that water can start flowing to it when it becomes cold enough (took about a good hour or so before water started filling the ice maker). Once the freezer was cold enough, water started filling the ice maker, and it begin making ice again.

Took two times getting the correct part, however after getting the correct part it took about 10-minutes to replace. Had to take the fan out. When you put the new drip pan in make sure it is positioned so that the guides on the pan aligns with slots in the bottom refrig brace, otherwise back pannel will not align correctly. The fan is ve ... Read more ry easy getting aligned in the new tray. May take a little effort. I do not know why the pan on a refrighterator that is less than 5-years old could start breaking into many pieces.

Ok, pretty easy repair when the parts are correct (first part was faulty, parts select quickly sent me a new one)

First is removal, these tubes are in there very tight, they can be pulled out but weaken the lines and it is not likely to work without severly stretching the line to the point of breakage, if you have to cut them d ... Read more o so carefully and take off as little tubing as possible as you need the length to feed from top to bottom.

Once you have cut all the lines, or pulled them out (I was able to get 2 out without cutting) then make sure the edges are smooth, attach the inlet valve to the plate and just push them tightly into the new valve making sure you route the lines correctly.

Turn everything on and run the water line to see if it works. If no leaks, screw it back to the refrigerator and you are good to go. Takes maybe 20 minutes at most.

First I removed the Ice bin, I then loosened the ice bin rail under the ice maker and removed the screw that attached the bottom of the ice maker to the side of the fridge. I unplugged the power to Ice Maker from the back of the fridge and unscreewed the two screws that secured the ice maker to the fridge. This allowed the Ice Maker to ... Read more be removed from the fridge. To replace the new ice maker I simply repeated the steps in reverse.

First I removed the drawers above the pantry drawer. Then I took out the pantry drawer. I unsrewed 3 screws that attached the part to the refreg. I then removed the rails that were attached to the part I was repalcing and put them on the new part. I then install the new part. Put the firg back together. It was extremely easy and took abou ... Read more t 5 minutes to do.

Unsnap damper louver cover using only your fingernails at bottom. Remove two phillips screws from damper cover. Remove styrofoam molded insulation. Squeeze electrical connector to release latch; unplug connector. Release latches on both sides of damper control while gently pulling on damper control unit to remove it. Install new unit by d ... Read more oing above steps in reverse. Damper door may move when electrics connected; keep fingers clear.
Amana would not honor our extended warranty that we paid $65 for, saying that noises are not covered. Im glad that Partselect supplied the part quick and and a great price. The frig is quiet for the first time in 2 years!

Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installin ... Read more g the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.

This is the 2nd time I had have had to replace the center rail in 2 years....