ABB1921 Refrigerator - Parts

This long harness thermistor kit is what helps monitor and regulate the temperature inside your refrigerator. It can be located in either the freezer compartment near the evaporator coils or in the fresh food compartment near the airflow channels, depending on the model. If you notice issues like excessive icing in the freezer, inadequate...Read more cooling in the refrigerator, temperature fluctuations, or error messages on the display panel, it indicates a potential problem with the thermistor. Since your fridge will not be able to maintain the desired temperature, this results in food spoilage, inefficient cooling, and potential damage to the cooling components. To replace the thermistor, disconnect it from the connector plug or wiring harness and remove any mounting brackets or clips using a screwdriver if necessary. Remember to consult your user manual to determine the required number of thermistors, as they are sold individually as OEM replacement parts.

This part mounts on the crisper drawer cover and is used to limit the amount of air that gets into the crisper.

The icemaker shut off arm, used in a refrigerator, gives the icemaker a signal to stop making ice once the bin has a reached a certain limit. This helps monitor ice production. If your icemaker is not making ice properly or consistently, replacing this part could be a solution to your problem. The tools required for this installation are ...Read morea 1/4 inch nut driver, a Phillips screwdriver, and needle nose pliers. Refer to the manual guide provided by the manufacturer for further guidance and instructions. Remember to safely store food when the refrigerator power is off to keep it from deteriorating.

The fan blade is used to blow air over the condenser.

The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact icemaker mold. This valve is used on side by side or bottom mount refrigerators.

The ice bucket in your freezer catches and holds the ice when it is released by the icemaker. If your ice bucket is cracked or damaged, you may need to replace it to prevent a potential leak. This part is made of white plastic and is sold individually. This ice bucket is approximately 15 inches long by 12 inches wide. Many of our customer...Read mores have rated this repair as very easy. To complete this repair, simply remove the old ice bucket and replace it with the new one. Be sure to remove any broken pieces of the old ice bucket before replacing it.

This defrost thermostat is a temperature sensing mechanism used in freezers and refrigerators. The thermostat senses the rise in evaporator temperature during a defrost cycle and turns the defrost heater off once frost is melted from the coils. If the freezer is not defrosting, or the freezer section is too warm, it is best to replace the...Read more thermostat to fix the problem. The tools needed for this project are: 1/4 inch nut driver, flat blade screwdriver, needle nose pliers, wire strippers, and pair of wire nuts. Remember to unplug your appliance from the power source for safety and refer to the manual provided by the manufacturer for installation instructions.

Sold individually.

This is an evaporator fan motor, it is 115 volts and 60 hertz and it is for your refrigerator/freezer. You will need to replace this part if your appliance is too warm or getting noisy. This evaporator fan motor is located in the back of the freezer. This part circulates air over the refrigerator coils. These coils will convert the heat i...Read morento cool air, which is then circulated throughout your appliance. To replace this part you will need a 1/4-inch nut driver and a pair of needle nose pliers.

The compression nut is used as a connection between the water supply line and other components in your refrigerator such as your ice maker and your water dispenser. Tools required for this repair include a pair of pliers and a socket set. Before installing this part you should take all perishable foods out of your refrigerator and store t...Read morehem somewhere cool, unplug the refrigerator from the power source, and shut off the water supply. This repair may require you to wear work gloves to protect your hands, and is considered an easy do-it-yourself fix.

Sold individually.

This wheel is sold individually. It is located on the bottom of the refrigerator.