Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AA3111 > Parts

AA3111 Amana Washer - Parts

All parts for the Amana Washer AA3111

Below is a list of all parts for the Amana Washer AA3111 - Top Loading. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the AA3111
1-14 of 260
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below....

$7.00

Retaining Ring

The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place or is damaged. Some the symptoms could be that your dryer does not tumble, it makes a loud buzzing noise, or if it pumps, but will not spin. The tools needed for this project are a putty knife, 5/16 nut driver, and snap ring pliers. Refer to the installation video and diagram for further instructions and guidance. Customers ranked this replacement project as easy.

$2.96

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$7.69

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

$4.63

Spring Retaining Clip

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrat...

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

$2.96

Screw

Sold Individually.

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$4.37

Inlet Hose Washer

This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to crea...

$16.17

V-Style Drive Belt (32.5 inches long)

This v-style drive belt is thirty-two and a half inches long and half of an inch wide.

$2.96

Screw, 8-18 x 1/2

This screw is sold individually.

$5.20

Rubber Foot Pad

This foot pad is just over an inch in diameter. It is all black in color and is made entirely of rubber. This pad is used for the levelling legs of many washing machines.

$34.00

Main Tub Bearing Assembly

This triangular main tub bearing assembly is five inches long. It is made of metal.

$27.04

Inlet Hose Kit

This hose is almost 5 feet long and now comes with the washers for proper installation. It is used to bring water into your washer for the cycles.

All Parts for the AA3111
1-14 of 260