A89L-4-R Admiral Cooktop - Instructions

After examining the burner unit I noticed that one of the male contact spades was burned and look deformed. After removing the spade I discovered that it had been originally manufactured incorrectly. I went on line to try and find the part. I found it at this site . I ordered 2 of the spades and replaced the deformed spade and anothe ... Read more r one that looked like it had gotten a little hot. She tried the unit and it worked perfectly. She had not used that burner unit for a very lengthy time. The investigation of the problem took a little time, but the repair went very fast. Moral is :" If a spade doesn't look right, it probably isn't", but either the individual spade or plug can be replaced. This site is now my "GO TO" place for parts.

I found the received switch (PS12070192) a poor replacement for the original, or even the earlier replaced part (PS11744446, in 2016) I was going to replace since the press/return feature seemed slow to return.

The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out ... Read more at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.

I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.

I have reinstalled the earlier unit.

Is part# PS 11744446 no longer available?



James E Weimholt. [email protected]

Lifted range top, disconnected and labled wires from old switch, removed old switch, replaced wires on new switch, installed new switch.
NOTE: Local appliance store informed me that the electric cooktop was too old and that a replacement switch was not available and wanted to sell me a new cooktop for $795!
I found the switch ... Read more on PartSelect and repaired the cooktop. Total cost... UNDER THIRTY DOLLARS!!

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element ma ... Read more king sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.

Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.

dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.

used the supplied parts...very easy. The parts were exact replacements.

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan

Pulled out the old burners and put in the new ones.

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was h ... Read more orrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Easy to put into place and done....Could have called this in, because place of business is in Louisville, close to me. Delivery was quick.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover