A700S Maytag Washer - Instructions

Install belts.

I first removed the front panel of the washer and removed 2 screws holding the top of washer in place. I had to flip the top up. This allowed easy access to the tub. I then removed the agitator by removing the set screw on the lower portion. From there I loosened the mounting securing device by using the nail punch and hammer inside o ... Read more f the tub (it was loosened by turning it clockwise). The tub was now loose and I removed it from the washer. Next I removed the torx set screw and the tapered hub unit (cork on it). It had to be again loosened with the hammer and nail punch and turning it clockwise. This exposed the part that needed to be replaced. I replaced the old with the new and the washer now works great with no leaks! Be sure to clean everything you remove that will be reassembled.

Observed source of leak by lying on floor behind washing machine and placing hand in likely spots. Found water injector hose was source. Searched web for instructions to open up washing machine: 2 screws at bottom of front panel, then 2 screws at top inside after removing front panel. Easy after that. Lots of rust and rusty screws and ru ... Read more sty tinnerman nuts; had to grind off one of the screws with dremel tool.

Used duct tape as the video provided instructed and also to hold second hinge lid ball in place. Firmly pushed down on the lid until it easily popped in place.

Received drain pump by fed ex, put it on in 15 minutes. . . My wife was very happy again. . . .

Tilt the washer sideways. Remove belts,Remove front panel, loosen two hoses, loosen three small nuts. Take out old pump and install new new pump vise versa. Video provided by partselect very helpful.

Unhooked water and drain lines, Unplugged electrical. Removed the two phillips screws at the bottom of the front cover. Removed the Front cover. TIpped machine backwards at about a 45 degree angle using a 2x4 to support the machine. Removed the pump belt and the drive belt. Installed the old pump belt and the new drive belt. Loosene ... Read more d the 3 each 5/16" bolts holding the pump mechanism and moved pump to the left. Moved pump to right to tighten pump belt and tightened the left pump bolt. Loosend the one pump bolt and pulled the motor to the left to tighten the drive belt and holding in this position I tightened the pump screws, Pump belt was now looser than the drive belt. Ran washer and it worked perfectly.

Received wrong springs for my model had too use combo old spring with the two new (too long) springs to get the tension on the belts. For now it working. Did not contact you due shipping took so long and two delay date change by FedEx ground. I didn't want to go thru another delivery nightmare. Thanks for the time.

First I removed the two screws to pull off the front panel. I then removed the two screws (1/4 inch head) in the upper front corners. Removed clamp from siphon break and carefully worked off hose. After a couple of failed efforts to put hose on dry I put some o-ring type grease on the barb and it went on easier. The clamp was a bit diff ... Read more icult too but take your time and it will go on. Putting injector end in tub required patients. Reassembly was reverse of above. All good for another 25 years!

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wa ... Read more ll box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.

After looking up the problem on the PartSelect website, which indicated the problem could be with the tumbler (drum) belt, I watched the instructional video, which was very helpful, as the dryer in the video was exactly the same as mine. After removing the power cord from the wall and separating the exhaust vent pipes from the dryer, I f ... Read more ollowed the instructions for removing the front panel, the front bulkhead, the drum and the old belt, which was worn and somewhat stretched. I then followed the instructions for installing the new belt, but I found it was easier for me to remove the back access panel in order to complete the installation of the belt around the drive pulley and tension pulley wheels as I wanted to see what I was doing as opposed to just "feeling" the belt to ensure a proper installation (e.g., new belt not twisted). Once I removed the drum, and before I put in the new belt, I also took the opportunity to use my shop vacuum (and you really need a shop vac for its power)to remove 25 years of rubber dust from the old belt, house dust, and packed lint from inside the exhaust fan, cabinet, and the vent pipes (and a dead field mouse that had crawled into the dryer through the outside vent pipe and had gotten trapped in the exhaust fan). I also examined the heater tubes to insure no lint was inside that and spun the fan blades by hand to make sure the motor shaft was not worn. Once I was satisfied that the installation of the belt was done properly, I put the drum back on, reinstalled the front bulkhead (checking to make sure the felt gaskets were in place, as recommended in the video) and reattached the front panel. I also took the opportunity to touch up the accumulated minor nicks and scratches ion the cabinet with refrigerator enamel. Now that the new belt is on, the dryer no longer vibrates, and with the dust, lint and mouse removed, dryer is operating much more efficiently. Remember to re-balance the dryer using a carpenter's level to minimize any latent vibration. Note that the actual removal and replacement of the belt took me about 30 minutes, and the rest of the cleaning, reattaching of the vent pipes, and balancing, etc. took about two hours.

I viewed and followed the PartSelect Instruction Video. My only problem was reattaching the door after the hinges fell off.Everything fell into place as the video indicated. After I regrouped I was able to put the hinges back and then I was able to reattach the side panel very easily as the vedio indicated. Thanks for everything.

Frist take off front of the washer, removed old belts and then put on the new. very easy.

I was only missing one of the bumpers but that was in pretty poor shape so I replaced them both. It didn't take much to do. Just pressed the bumper into place and Viola! instant gratification.

My 13yr old son and I fixed the washer in about 5 minutes. It was very simple and easy to repair considering I had never done it before.