A100 - Parts

This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these belts has worn or stretched out. This results in the belt losing its grip and no longer driving the pump. The pump belt is black and made of rubber. The pump belt ...Read moreis located between the motor and pump underneath the washer. Simply remove the belt and hook the new one around the pulley. You may need to loosen or tighten the belt to ensure it is set in place properly.

This is a drip bowl, and it is used in conjunction with your range. The function of this part is to sit underneath your stove top burner element. This will allow the bowl to catch any spills that fall through the burner while cooking. This model is chrome has a chrome color trim, it measures 8 inches in diameter, and is sold individually....Read more Before installing this part, you must wait until the surface of your range is cool to the touch. Replacing the drip bowl will require you to touch the burner on your stove top.

The drip bowl is found under the 6-inch burner on your range. This square chrome stove top drip pan is intended for use with electric ranges. It has a 2-inch inner hole diameter and 7-inch outer diameter. Drip bowls should be cleaned regularly, and replaced when too much food and debris has been burned or stuck to it, making it too hard t...Read moreo clean. You should replace your drip pan if it is rusted or damaged. Grease, oil, and food can spill into your unit and become a fire hazard. This drip pan is dishwasher safe and is sold individually.

The tools you will need to replace the surface burner receptacle kit on your range include a Phillips screw driver, and a pair of wire strippers. Before doing this repair, make sure to disconnect your appliance from the power supply and wear work gloves to protect your hands. The surface burner receptacle kit comes with a plastic block, h...Read moreigh temperature wire nuts, a metal bracket, and wires. This part functions as the connection between the wire harness and the surface element in your range.

This kit comes with a hub assembly, agitator seal, and spanner nut. If your washer leaks once it is full (with or without clothes in it) or leaks during agitation, then you should replace the seal. This part will also fix symptoms such as loud noises or the washer not agitating. The seal may become damaged or deteriorate over time and wil...Read morel need to be replaced. The mounting stem goes between the two tubs and seals the water into the tubs. When the water leaks, it goes into the bearing, which will cause it to also go bad, which is why you will likely change these at the same time.

This is replacement high temperature adhesive for your washer and dryer. It is designed to hold objects together, and will not disintegrate at a high temperature. This is a 2-ounce tube of adhesive that is sold individually. This is an OEM product sourced directly from the manufacturer.

This screw is sold individually.

This 8 inch surface burner with reinforced delta frame carries 2100 watts and 240 volts. It has five turns and is compatible with many electric ranges. Its center medallion is all black in color.

This is a surface element for the stove top on your range. It supplies heat to the top of the range cooking area. This model is 2100 watts and is eight inches in diameter. It has looped terminal ends, and five turns. The most common reason for needing to replace this part is if your current element is not retaining heat. The first step to...Read more this repair is to make sure the burner control is set to off, and that the element is cool to the touch.

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on th...Read moree appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.

The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers. ...Read moreMany of our customers have rated this repair as very easy. To complete the repair, turn the old leg counter clockwise to remove it. Then, simply remove the old pad and replace it with the new one. Finally, re-attach the leg by turning clockwise. Ensure that the washer is level, and adjust the leg accordingly if it is not.