99521 (1988) Kenmore Range - Instructions

Easy.... UNPLUG THE STOVE FROM THE 240 VOLT OUTLET & READ THE DIRECTIONS THAT COME WITH THE NEW PART !! Removed upper rear cover panel 8 screws & removed panel, removed knob & 2 screws from front of control unit (on the control panel), pulled the control off the panel from the rear, removed the wires on the rear of control & connected th ... Read more em to the SAME terminals on the new control (one at a time). Then installed the new control by reversing the procedure above. Took about 15 minutes. IMPORTANT HINTS: 1) Make sure you save the little black pressure clip from the control stem on the new control, if you need to break-off the little part at the end of the stem. You will need to push the clip back into the recess on the new stem, in order for the knob to stay on the stem when you put it back on; 2) Use a needle-nose plier to pull the wire clips from the old control terminals & push them onto the same terminals on the new control, one at a time so the wiring is correct.

Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette!

removed drawer below oven, reached under stove and unplugged from outlet, pulled stove out from between cabinets, removed the 8 screws with 5/16 nutdriver from back panel and removed the panel, removed knob from switch , measured length of stem on old switch and compared it to the new switch ( my old switch stems was shorter than the new ... Read more one so using a pair of pliers I shortened stem per instructions that came with new switch, this was very easy to do ), removed the two screws holding switch to stove and removed the old switch, then I transfered one wire at a time from the old switch to the new one until I had all the wires connected to the new one, used same two screws holding old switch to the stove to mount the new switch to the stove and put knob from old switch onto the new one, installed back panel to stove using the same 8 screws, pushed stove back into place between the cabinets and plugged the stove into the outlet, put drawer back in place below oven door, reset clock and tried out the new switch, so far so good only time well tell if I fixed my problem because it only happens once in awhile

I unplugged the stove from the outlet, then removed the two burners I was going to be working on and the drip pans. Then I raised the top part of the stove and removed the screws holding the plug-in blocks to the stove. Then I cut the two wires going to the old plug-in block and stripped the wires back to match the new wire parts. Then I ... Read more placed the sleeves over the new wires, then I placed the new wire beside the wire I stripped on the stove and screw on the wire cap making sure it was tight. I repeated this three more times, once I had all four wires connected I then placed the sleeves over the connections and heated them up until they were formed around the connection. Once I had all the connections done I placed one wire at a time into the plug-in block until it locked into place ( I looked at my old plug-in blocks first to make sure I placed the new wires in the correct way ).I then used the metal mounting bracket that matched my old ones and snapped the correct one onto each plug-in block. Before mounting them onto the stove I compared them to my old ones to make sure they were correct. Then I used the new screws to mount them to the stove. I took a second look at everything I had done before closing the top cover of my stove. After lowering the cover back into place I put both the drip covers in place and then installed the burners.I then plugged the stove back into the outlet and tried the burners. This was very simple and the video on the web site shows this very well which made my job very simple.

I received my ordered in less than a week. It was great. The day I got them I remove the old burners and replaced them with the new ones. It took me about 3 minutes total. I was then able to cook my Christmas dinner with out any problems.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

two Phillips head screws hold the oven unit in. It culls out and the wires just disconnect. Reinstall in reverse and test.. The burner socket I cut the wires from the old socket and splice the new pigtails onto the existing wires and install the socket. The instructions in the package are good for people that aren't used to doing repairs.

After shutting off the power, I removed the door and oven racks. Then, by using a screwdriver, I removed each element one at a time and replaced with the new element. Each element pulled away from the back wall and was connected electrically by Sta-Kon connectors. All went well, and the unit was operational in about 30 minutes. I stil ... Read more l have to remove the oven from the wall to replaced the two door springs.

Turn Off Breaker.

Removed oven racks....

Removed two screws holding element in place...

Disconnect spade lug connectors from old heating element.

Connected spade lug connectors to new heating element.

Reinstall 2 screws holding element.....

Replace oven racks.

T ... Read more urn Breakers back On.

Done 10 Min. Install

Removed the two Philips head screws that attach the element to the back wall of the oven. Pulled off the two wire terminals from the spades on the back of the element. Pushed the two wire terminals onto the spades on the back of the new element. Noticed that one was not tight, so disconnected, squeezed down the wire terminal, and reco ... Read more nnected. Inserted the two screws that attach the element to the back wall of the oven. Element works fine.

Purchased 2 piece broiler pan from this site

This is an easy fix. Just before the holidays, it was imperative that this appliance be in top shape. Since the door 'hung' wrong, it was determined that the hinge pin broke. Remove the 2 phillips head screws on the door and open the door to the to a 15 degree opening. This position allows you to slip the door off the hinge levers. N ... Read more ow that the door is off, replace the hinge pin and slip the retainer ring on with a screw driver blade to push it on the pin. Slide the door back on the levers and fasten the retainer screws. DONE!

Shut down breaker; remove stove back cover plate (8 screws); remove the control knob; remove knob screws (2); simply remove one wire at a time and replace the coresponding wire to the new control unit; remove the snap ring on the knob bar and snap off to fit the proper length; place the control unit in position and reinstall the 2 screws; ... Read more reinstall the back panel; position stove and turn throw the stove breaker on; test the burner control.

My husband wanted me to call a repair man but I had read online how easy it was. I received my element in one day from Fresno, CA and followed the instructions given by others on line. I couldn't believe how easy it was. The most difficult was removing the connectors because they were stuck. I used needle nose pliers as someone sugges ... Read more ted. Saved the cost of a repair man.

First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.