99138 (1988) Kenmore Range - Instructions

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

First I disconnected the power. Then I removed the burner element and drip pan. Using the screwdriver I removed the single screw that holds the terminal block in place. I then cut the 2 wires to the old terminal block. I connected the wires of the new block to the existing wires using the supplied wire nuts. Next I slipped the supplied heat shrink tubing over the wire nut and wires and using the heat gun I applied heat to the shrink wrap. Finally I reinstalled the new terminal block using the old screw and re-installed the drip pan and burner. I repeated the procedure for 2 other burners that were exhibiting the same problem. All work perfectly.

Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)

The terminal bloctk silver attachment did not fit our stove. We had to use the old one and take off a little of the nipple that snapped it into place .used a bench grinder for that.The rest was easy. Used a heat gun paint stripper to shrink the shrink wrap,Saved a big repair bill.

Easy

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.

I removed the old element and replaced it with a new part. It was very simple.

The power was turned off. The elemnt wiring was removed. The new one was installed in reverse order. Power back on and the oven tested just fine.

Turned off power. Removed oven racks. Removed the 2 screws that held the element in place. Pulled element out about 3 in. & disconnected 3 wires. Placed new element, reconnected 3 wires & reconnected the 2 screws that hold element in place. Turned power back on & it works great!!. Was very pleased at how easy it was & also how fast I received the part, which was day after I ordered it.

I first removed the two hex head screws, pulled the element slowly forward about four to five inches and disconected the two wires on the old element.
I removed the old element and attached the wires to the new element. I then slowly pushed it back into the rear wall of the oven, carefull not to disturb the insulation around the opening and replaced the two screws that hold the element to the back wall of the oven. It was easy enough to do, even for a woman. I turned on the oven and it worked great. No problems so far.

Had to take back panel off of the inside of the oven to get to the screws to remove the old element and attache the new. Removed the two screws to remove the old, pulled it out unattached the wires and attached the new one.

Everything was very easy: identifying the right part was very easy on the website, the part came quicker than I expected, and my wife replaced the stove element before I even got home from work. She just pulled the old one out like she would to clean the top of the stove, and put the new one back in. Have had several awesome cups of coffee since the replacement.

First shut off power to the store and used a socket set to remove 2 screws and disconnnect the element. Connected the new element but had to use the old screws as the new ones did not work with my appliance.

I pulled out the old burner - put the new one in and I was done. No tools required.

The first burner I received from PartSelect was warped. I called on Friday morning to see about returning it and ordering a new one. The CSR was very helpful and I was totally surprised to have the replacement arrive the very next day since I didn't ask for a Saturday delivery. I will definitely use PartSelect again.

The hardest part was working in the oven.

Turn off power
Open Oven Door, remove racks
Remove two mounting screws with nut driver.
Slide the element out to expose the wire connections.
Remove the screws and pull the element out.
Place the new element in oven.
Clamp on to each of the terminals with vice grips to keep from bending the element and install the screws.
Slide the element back into place and put the two mounting screws back in.

Put the racks back in and turn on the power and test. You may get a little smoke off the new coil.

Like I said the hardest part is leaning into the oven to attach the screws, do not sit on the oven door.

Did it By Hand
Your Shipment Time Excellant
Order it Mon. Received it Wed.


Thank You