Models
>
9825VUV
9825VUV Magic Chef Wall Oven - Overview
Sections of the 9825VUV
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$11.73
In Stock
Long Oven Sensor
PartSelect #: PS1570174
Manufacturer #: 12001656
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of...
$34.75
In Stock
Range Bake Element
PartSelect #: PS11757472
Manufacturer #: WPY04000066
The bake element is the heating element that is found at the bottom of the oven and is responsible for 90 percent of the bake heating. This spade style bake element is 16 inches wide, and connects wit...
$103.52
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Terminal Block
PartSelect #: PS11750972
Manufacturer #: WPW10245259
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness...
$34.09
In Stock
Oven Rack
PartSelect #: PS1642683
Manufacturer #: 71003346
This oven rack is sold individually. The functionality of the oven rack is to provide a reliable cooking surface for cookware inside your oven. This specific oven rack is roughly eighteen inches wide ...
No Longer Available
Light Cover Lens
PartSelect #: PS11747414
Manufacturer #: WP9781049
The light cover lens in your oven is designed to protect the light bulb. If your light cover lens is damaged, you will need to replace it. This part is made of clear glass and is roughly 3 inches in d...
$64.44
In Stock
Clock Knob - black
PartSelect #: PS11744674
Manufacturer #: WP7711P492-60
The clock knob attaches to the center of the oven control panel and is used to adjust the built-in clock. This clock knob is less than an inch in diameter. It is all black in color and is made of plas...
$20.95
In Stock
Frame Screw
PartSelect #: PS11743908
Manufacturer #: WP7101P126-60
Sold Individually.
$7.76
In Stock
Door Hinge
PartSelect #: PS2080677
Manufacturer #: 74001984
This door hinge is a genuine OEM replacement part for your wall oven. Replacing this part will require partially removing your oven from the wall, to access the hinge. This part contains one hinge, al...
$92.23
In Stock
Stand Mixer Screw
PartSelect #: PS11742292
Manufacturer #: WP4159193
This screw is sold individually.
$8.63
In Stock
Questions And Answers for 9825VUV
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Karen
November 14, 2023
The oven will not get above 200 degrees does that mean it needs a new thermostat
For model number 9825VUV
Hi Karen, Thank you for writing. We suggest testing the Long Oven Sensor. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
Long Oven Sensor
$34.75
In Stock
- < Prev
- 1
- Next >
Common Symptoms of the 9825VUV
[Viewing 10 of 10]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Will not program
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read more
reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read less
Parts Used:
-
David from Westford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
156 of 196 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bottom heating element in oven disintegrated
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I threw away the old pieces.
Then I connected the two wires on the new element. I pushed the wires back in the insulation in the wall of the cabinet. Then I inserted the two screws and t ... Read more ightened them in.
SUPER EASY!!!!!
This $40 part saved me $1500 on a new double wall oven.
Then I connected the two wires on the new element. I pushed the wires back in the insulation in the wall of the cabinet. Then I inserted the two screws and t ... Read more ightened them in.
SUPER EASY!!!!!
This $40 part saved me $1500 on a new double wall oven.
Read less
Parts Used:
-
DENISE from GERMANTOWN, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
66 of 71 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F1-1 code
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa
... Read more
ilure to do so will cause the plastic plug connector to melt from oven heat.
Read less
Parts Used:
-
charles from marstons mills, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
74 of 99 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!