92198 LG Dryer - Instructions

The lint screen that this company sent was 3x too large. I called to return/exchange it. No one available - go to customer service.
I went to customer service and entered my email address and the order number (while I was looking at the original order1). The email and order number could not be found.

I am still wai ... Read more ting to hear from someone from the company to get a RMA and return label! Will NEVER use this company again.
Vivien Joebchen

Initially replaced igniter. Didn't think it was bad though. Read other suggestions on another website. None were the correct diagnosis for my situation. And when I figured it out they did not offer correct part. The dryer thermistor temp sensor (probe sensor) is what I replaced. Found it on Parts Select. I did replace other parts also. Bu ... Read more t that's the one that ultimately was the issue.
Was not hard at all if one is even a little handy.

Pull off the top and front of the dryer and reached in and replaced the part it was easy. Had to clean all the dryer out real good with from the lint

I ordered the lint filter screen and when it arrived it looked exactly like the old one. It should have been nothing more than remove the old one and slide the new one in place.

Unfortunately, the new screen was about 1/2" wider than the old one and would not fit into the guide. After consulting by phone with your parts exp ... Read more ert, we confirmed the model number and serial numbers, and eventually concluded that a design change must have been made by the manufacturer. We thought the only solution would be to also purchase the corresponding filter guide. So I ordered the guide. When it arrived, I installed it - a very difficult installation requiring putting my head and one shoulder into the dryer in order to get the screws out. (A long arm with two elbows would be nice.) After I got the old guide out, I discovered that it was exactly like the new one - 1/2" too narrow for the new filter screen. I reinstalled the old guide and returned both parts.

The dryer filter screen still has a hole in it and I am now waiting for my refund. I have no idea how to solve the problem.

The filter screen part number is 24053607, order number 18265310.

The guide part number is 24145665, order number 18348658.

Model number: DLE3170W

Serial number: 603KWMK6T539

I replaced the thermistor, then the gas ignitor which were easy to get to once the drum was out. The gas is still not igniting so not sure where to go from here. Putting the drum belt back on took some muscle. But then I'm 71.

I put the dryer information into my browser and found PartSelect had the exact replacement part I needed. I ordered the part and it came is just a few days. I removed the part from the excellent packaging, removed the cracked lint filter from the dryer, replaced it with the new lint filter and done!
Among things I've successfully r ... Read more epaired, this was the easiest and best job I've ever done. Quick, Easy and painless.
Thanks for asking!

When manufacturer confirmed the part would fit without an adapter, it was the easiest DIY task ever undertaken.

Ordered a new one and installed it in a matter of seconds.
Not difficult!

Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.

There’s all sorts of videos on it I watched. It was actually very simple

Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descr ... Read more iptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.

Completely had to dismantle the dryer to get to the igniter.
The screw holding the igniter is a SOB to get at for extraction, and even worse putting back.,

Simple replacement

FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOT ... Read more OR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.

I watched a YouTube video with how to take the dryer apart and remove the sensors. I followed the what the instructions were removing the top of the dryer and then the front panel. Once that was removed it was a matter of removing 7 more screws and the lint collector piece came off. Popped the sensor pieces out. Cleaned the inside of the ... Read more dryer and reinstalled a total of 5 parts and dryer is working fine and the clothes are drying in the allotted time it use to take.