919165230 Craftsman Compressor - Parts

Frequently referred to as a Drain Plug, this Drain Valve is used to drain any condensation that has collected inside the tank to prevent the tank from rusting. It is not part of a kit or assembly, is sold individually, made of brass, is gold, and will be found at the bottom of the air tank. This part will need to be replaced when it is ...Read moreno longer able to provide a proper seal, or if it is visibly worn or damaged. You will need a wrench to complete this repair. Customers rate this repair as Easy.

The piston ring between the cylinder and piston within an air compressor is used to form a tight compression seal to allow the piston to move up and down without touching the cylinder wall, as well as dissipate heat evenly away from the piston and align the piston properly within the cylinder. This piston ring is designed for and compatib...Read morele with various models of air compressor and is sold as an individual OEM part. This piston ring has a 48mm (1.89-inch) inner-diameter and 62.5mm (2.46-inch) outer-diameter and is specially coated and oil-free. If you notice increased noise and vibrations or simply poor performance from your air compressor, there is likely something wrong with the piston ring or pistons that would warrant an inspection. To replace this piston ring, first turn your air compressor off and disconnect the spark plug. Then, disassemble the cylinder by removing the cylinder head/cover or any other components blocking access to the pistons, referencing your user manual for the exact location. Once inside the cylinder, slide out the piston very carefully, and take note of its orientation. Remove the old ring from between the cylinder and piston and press the new one on with firm and even pressure. Now, reassemble the air compressor and monitor its performance.

This fan is an exact replacement part for use in air compressors and is sourced directly from the manufacturer. It is made of durable black plastic and is used to cool the compressor during operation. It is not part of a kit or assembly and is sold individually. This part is located on the end of the motor shaft and will be visibly brok...Read moreen or worn when it needs to be replaced. You will need a screwdriver, a socket set, and a drill to complete this repair. Customers rate this repair as Easy.

Sourced directly from the manufacturer, this part is an exact replacement for various air compressors. Its primary purpose is to control the airflow through the pump. This part is an assembly that includes the plate gasket and seals. When this part is malfunctioning, the tank will take longer to fill or will not be able to fill at all. I...Read moret will need to be replaced once it becomes damaged or worn. You will need a wrench set and a socket set to complete this repair. Customers rated this repair as Easy.

This replacement foam filter is a high quality item that is specially designed for use with Craftsman air compressors. Its purpose is to ensure the air that goes into the engine is free of dust and other contaminants. One durable foam air filter is included per order.

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with air compressors. The three wire cord is encased in a durable jacket and includes terminals at the end of the wires. The cord is used to relay electricity from the outlet to the switch assembly. This item is available as an individual replacement part.

This wheel is a genuine OEM replacement part used in portable air compressors. It consists of a plastic rim and rubber tire with an outer diameter of 9.5 inches. It is held in place on the compressor axle by a shoulder bolt and nut. The wheel allows the equipment to move smoothly during use. If the tire is punctured, or the rim is damaged...Read more, the wheel will need to be replaced to restore the portability of your equipment. If the nut and bolt are worn down, it is recommended to replace them at the same time. Remove the nut and bolt that secure the wheel and pull it off the axle. Place the new wheel in position and secure it with the fasteners (sold separately). Each wheel is sold individually.

This is an authentic Craftsman replacement part manufactured for use with air compressors. The muffler is used to reduce the noise created by the compressor while running. This muffler is available as an individual replacement part.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is a genuine OEM sourced part used on a variety of Craftsman air compressors. The air filter retainer secures the foam filter onto the head in the front shroud. This plastic component is sold individually, and a wrench may be needed to make the replacement. Please refer to the manual for the further safety and repair instructions.

This replacement regulator is a high quality item that is supplied from original equipment manufacturer for use with air compressors. It allows user to adjust the pressure of the air coming from the tank to the desired level. Make sure to unplug the air compressor release all the air from the tank before installing this part. Please note ...Read moreone durable metal three port regulator with a plastic knob is included per order.