919153420 Craftsman Compressor - Parts

Frequently referred to as a Drain Plug, this Drain Valve is used to drain any condensation that has collected inside the tank to prevent the tank from rusting. It is not part of a kit or assembly, is sold individually, made of brass, is gold, and will be found at the bottom of the air tank. This part will need to be replaced when it is ...Read moreno longer able to provide a proper seal, or if it is visibly worn or damaged. You will need a wrench to complete this repair. Customers rate this repair as Easy.

This replacement regulator is a high quality item that is supplied from original equipment manufacturer for use with air compressors. It allows user to adjust the pressure of the air coming from the tank to the desired level. Make sure to unplug the air compressor release all the air from the tank before installing this part. Please note ...Read moreone durable metal three port regulator with a plastic knob is included per order.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling • The O-ring has ragged, tattered edges. Thes...Read moree are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.

This part is sold individually and helps to support the compressor. The rubber bumper recess attaches to the tank. A screwdriver may be helpful when replacing this part. It may become broken and will need to be replaced. This is an OEM part directly sourced from the manufacturer for use in compressors made by Porter Cable, DeVilbiss, Black & Decker, DeWALT, and Bostitch.

This is an authentic OEM part for use with Craftsman Compressors. The check valve lets pressurized air flow into the tank and prevents air from flowing back into the pump. A failed check valve will apply high air pressure to the head of the pump preventing the motor from restarting once the tank has filled. The most common reason for repl...Read moreacing the check valve is if the motor starts with an empty tank but won't start when the tank is full. This part is sold individually. The tool that you will need to replace the check valve is an adjustable wrench and Teflon tape.

This is an authentic replacement part that has been OEM sourced to be used with Porter Cable, DeVilbiss, and Black and Decker air compressors. The metal nut is commonly used to connect the outlet tube to the cylinder head assembly. This item is available as an individual replacement part, a hex wrench is needed for this repair.

This is a genuine replacement part manufactured for use with air compressors from DeWalt. This part creates an airtight seal between the elbow and the tube. You may need a wrench to replace this part. This assembly but sleeve is sold individually and made of metal.

This is a genuine replacement screw which is supplied directly from the original equipment manufacturer for use with Craftsman air compressors. This hex head screw has multiple applications, please make sure to check appropriate diagrams of your model for the correct location and use of this hardware. Note this high-quality metal screw is sold individually.

This is an OEM part sourced directly from the manufacturer. The adapter is designed for use in compressors from DeVilbiss, Black & Decker, Delta, and Porter Cable. This part is made of metal, and may be used to connect the regulator to the tank. You will require a wrench when replacing this part. This item is sold individually.