9119352 Kenmore Range - Instructions

I actually don't remember if instructions came with purchase. I have purchased appliance parts from here before and they did on previous times. I watched a couple of YouTube videos because I'm a visual guy (as I think most guys are) and the only difference between my reality and the video was I had nuts holding the element in place and ... Read more the video had screws holding it in place. Extremely easy!! TURN OFF POWER TO STOVE.....PLEASE. Confirm power is OFF (clock not working...range wont turn on....something like that) Take oven door off hinges (mine just slid off without any problem). Remove defective element from oven. In the back there are two screws or bolts, take them out. SLOWLY pull old element out. Be careful and look for the insulation that will try to come out of the hole and watch for the wires that are attached to the element. The wires will come out far enough for you to work with them (about 6" or so). Be very careful NOT to jerk wires through holes too much or damage them. Remove wires from element. I used two pliers, one on element and one on wire crimp...I also sprayed wd40 on the connection prior and let it set for a short time before to loosen it up. Once separated, discard old element. Get new element and reverse the process. I reconnected wires, making sure to put them back in the exact same side they came off of. Ease the element power prongs back through the holes (VERY CAREFULLY, DON'T RUSH AND TEAR IT UP). The new element will fit exactly where the old one came off and just put the screws or bolts back in place and be VERY CAREFUL NOT TO STRIP THE SCREWS OR BOLTS. Turn power back on at breaker and turn on oven to check and see that it works. It should work great. This is the second part I've purchased from these guys and both jobs went flawlessly. I HIGHLY RECOMMEND these guys...plus it's almost the only place I could find to get the parts, but still they are great.

Super simple to repair, removed back cover on oven (after turning off breaker), removed old terminals from over, had to bend new element slightly close to terminals, installed new and replaced oven cover. Less than 15 minutes.

Very easy repair. Part came wrong the first time (my fault for ordering the wrong one). Called and ordered the correct one after a closer match to the original part. Delivered much quicker than promised (one day) and installation very easy. Will use this site for all future repairs.

I watched the video on the website then installed the part. In fact, I watched the video twice because I could not believe it was that easy. You can not do any better than PartSelect. Shipping is fast and the instructions are great. If I ever need a part for any appliance I will go to PartSelect.com first. Keep up the great work and thank ... Read more -you so much!

We were able to purchase the part and replace it for under $25. We took off the oven door and installed the new element in under 10 minutes.

First i turned off the main electricity for the oven. Then I removed the two screws with my socket wrench. Then i pulled the element out about 3 inches then disconnected the 2 wires that heated the element. I simply reversed the process to put in the new bake element and i was done.

Removed two scres that hold element in Place. Pulled out element about 3" and removed wire disconnect. Re-connected new element and re-installed mounting screws. Very easy. Parts were delivered promptly. Great service!!!! Thank you Parts select!!!!! Saved me a trip to Sears to purchas a new element or Stove.

I read the "easy to repair" story after I ordered my part and I felt like I coud do this on my own. (Female not much experience in repairs) I shut off circuit breaker...proceeded to take out element...could not get it to easiler come off...so I made the mistake of cutting the wire because it looked like that's what I needed to do. WORD TO ... Read more THE WISE...there are clamps that actually pull off the element..just need to pull a little. So my "easy" project was made more difficult because I didn't know this up front. Otherwise it would have been a breeze. I had to go to the hardware store and but new clamps and attach to the cut wire. Good news is my oven is now working and Parts.com was fast, cheaper than the GE parts place and great service.

pulled stove out from wall about a foot ans disconnected the electricity cord. removed the 2 screws holding the element in place and pulled it out a bout 3 inches and disconnected the two wires. attached the new element & pushed it in place and tighrened the 2 screws. hooked up the electric power, moved stove back in place & it was done ... Read more !

the only challenging thing realizing that the screws in the back weren't for a screw driver, they were for a very small wrench. Since I didn't have such a tool, I just used vice grips. It all went well though. The oven currently heats to 400 degrees in 7.5 min. I am quite happy.

Turned off circuit breaker for Range. Removed the 2 screws holding element and pulled wires attached to the element through holes. Disconnected the wires and attached new element. Had problem with one wire springing back into hole used paper clip to fish it back out of hole and then connected 2nd wire to heating element. Turned breaker ba ... Read more ck on and tested. Baked a cake. MMMMMMMM.

The hardest part of repair was moving the oven from the cabnets to unplug and gain access to rear of oven. Remove rear cover panel unplug two spade connectors attached to the heating element. Open oven door and remove the two screws holding the heating element to back of oven. Pull heating element out. Then slide the new element in an ... Read more d assemble in reverse order.

First I removed the two screws holding the element to the back of the oven. When I pulled the element out I disconnected the two wires and removed the element. I found the serial / part number on the existing part and order from PartSelect. The element arrived two days sooner than expected!! Replacing the element was a bit more difficu ... Read more lt in that I had to pull the stove away from the wall and remove the rear cover in order to pull the wires and element through the insulation in the back of the oven. Four screws held the rear cover, but once those were removed the element easily went into place and the repair was finished. Cleaning behind and under the stove took a few extra minutes but the entire repair only took about 30 minutes, plus the wait time for the part. Two tips, pliers were used to disconnect and reconnect the slip-on connectors. The connectors were pretty tight and reaching to the rear of the oven was difficult to get leverage to pull apart and reconnect. Also, the oven light caused considerable glare on my glasses so I taped the door button controlling the oven light and used a flashlight to see inside. Otherwise, a simple repair. PartSelect had the best price on the element and service and delivery were excellent!

Simply turned off the power (circuit box). Unscrewed the screws holding the element in place and detached the element from the wires. Replaced with the new element and replaced the screws. Turned the power back on. Easy as pie and saved lots of $$!

first i unplugged the stove to disconnect all power. next itried using pliers to unscrew the screws and was having a hard time so hubby got the adjustable wrench and it was much easier. after taking out the two screws, i pulled the element out about three inches and disconnected the element from the two wires that hold it in place. then i ... Read more snapped the new element in place just as the old one was and reattached the element to the stove using the two screws. after assuring that element was secure, i turned my oven on to 300 degrees and voila!!! we're cookin again!!!