911933 Kenmore Range - Instructions

This electric stove has a lift up top which I lifted to get at the block and follow the wire back to the terminal at the back of the the stove. I removed the 5 small lag screws holding the back in place, removed the backing followed the wires back to where they connected in the Stove On/Off Control, disconnected the two wires from the co ... Read more ntrol and then laid the new part in place rethreading and reconnecting the wires. I reinstalled the block and ran a test to ensure the burner operated correctly. After successful testing I disconnect the old block holder by removing the small lag screw, replace it with a new one that came with the replacement terminal block. I then inserted the block into the new holder carefully rolled up the excess wire and wrapped it in a couple of places with electrical tape and also secured it to the side of the stove, out of the way of operation with electrical tape, put the top down, plugged it back in and put it back in place. All told the repair took about 40 minutes. I was impressed with the speed of delivery, the quality of the product, the instructions for installation and the added bonus of getting a terminal block holder as part of the repair kit! Thank You for making me look like a genius!

I first turned off power, then I removed the old top oven heating element, I connected the new element to power supply then placed the element back into holders.

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

First I unplugged the stove. I then removed the control panel using a flat head screw driver. Then I removed the two screws (phillips head) holding the element in. Five wires had to be disconnected from the old element and placed on the new one. As I removed each wire from the burned out element, I placed it in the same place on the n ... Read more ew one. I then replacedd the element on the stove and put the control panel back in placed. I plugged the stove into the wall outlet and tested the element control. This whole procedure took no longer than about fifteen minutes.

Removed old racks and replaced with new racks.

Replace part an wires

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

Pulled burner out of socket and pushed new burner into socket. Took less than a minute.

unscrew the terminal block,pulled the old wires out,installed the new wires installed the new block

Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm ... Read more .

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the ... Read more switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

Switching out the part was reasonably easy. The hard part twas that over 15 years some of the other parts have dried out. The oven indicator light came loose and the tabs on the clock were broken. With the help of some glue & some Z bracket it is back together minus the oven indicator light. Not perfect but cheaper than buying a new one.

My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, ... Read more and they look great. The price is less than any other site I investigated.

My husband actually did the replacement but I did all the research online to find the right part. I wasn't sure we'd find it for our old stove but luckily we did and it works fine. Thanks for the super fast service!

I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!