9117898513 Kenmore Range - Instructions

I had to replace the ignitor. The wiring was simple. Just had to connect two wires. The difficult part was removing and replacing the ignitor. It is suspended by 2 screws that are very difficult to access.

The repair was easy and not very time consuming. It didn't take very long to fix the problem and thanks to this site, I was able to save the money I would have spent if a repair technician came out to do the same work. Now I can afford Christmas and cook too!

I removed the igniter by first removing the oven racks then the oven pan and oven catch pans. I open the lower draw to the oven and removed the drawer. I reached back under the oven and clipped the wires that run to the igniter and striped a half inch of plastic to expose the wire. I removed the igniter from the burner and replaced wit ... Read more h new igniter. I then fed the wires back through the hole the cut wires came out of and used the wire nuts supplied to connect. Replaced other parts in reverse order and tested. Works great.

First had to disconnect the old igniter by removing screw with a small wratchet wrench. Then pull out approximately 3" of wire from the old igniter, cut off old igniter, attache replacement igniter with supplied wire nuts, shove excess wire back into wiring compartment and then attach the new igniter.

I removed lower drawer, removed oven door,
took out rear screws to oven pan,removed screws that attatch ignighter to oven wall,disconnected wiring and removed old ignighter. reversed process to install new part. total repair time was about 20 minutes. Also take into consideration that i am a building contractor familiar to appliance ... Read more repair etc.

Removed bottom drawer removed door and racks and bottom shield.disconected two leads from igniter . then struggled to remove igniter. after ordering part readf comments from other men and the man who said he removed the burner hit it right on the head after the part arrived the very next day after ordering it i removed the burner attached ... Read more pig tails and had part installed and stove back together in 15 minutes. thanks good experience

1) use screwdriver to remove screws securing lower pan in oven (screws are at back of oven)
2) remove lower pain to expose igniter and burner
3) remove lower storage drawer
4) disconnect 2 igniter wires from where they are attached underneath
5) use nutdriver to remove burner from above and below (this makes it easier ... Read more to remove the igniter)
6) use nutdriver to remove the faulty igniter
7) cut off clips from faulty igniter leaving enough length to strip and then attach with ceramic caps to new igniter. (be sure you attach the right clip to the right wire)
8) reverse the process to install the new igniter.
20 minutes tops

frist tested ignitor with meter removed ignitor order
part , I recieved to my surprise next day I'm a very happy person

The biggest problem is to get down low enough and far enough back to be able to reach the igniter. Other tan that , it was a simple affair.Unscrew the old one and detach the wire nuts and reverse the procedure for the installation and hope the gas valve has'nt been affected

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd re ... Read more moved and the oven functions just fine.

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstal ... Read more led protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.

Take bottom drawer out, take two 1\4 inch drive screws out from back bottom of inside of oven. Take out protector plate . Remove 1\4 inch drive screws from bottom burner[back of oven] where drawer was. Extract burner. Rest is self explanitory. Good luck. . . . . .

First I removed the bottom oven drawer then
I removed the heat shields. I removed the two
wires that connected the igniter and the two screws holding the igniter and removed it. I
replaced a wire connector on one side of the
igniter. The other igniter wire I soldered together
to the other wire. Then I replaced ... Read more the igniter by
reconnecting the two mounting screws. Then I replaced the heat shields and the oven drawer.

I followed the advice in the previous repair stories as this was very helpful.

I didn't know if polarity on the igniter mattered, so to be safe I marked the same wire on the old igniter and the corresponding wire on the new ignitor and plug, so it would be hooked up with the same polarity.

I took the burner element ... Read more out to make it easier to replace the ignitor. I made sure to leave plenty of wire when cutting the connectors off the old igniter. Hooked everything up and it worked perfectly.

well,as with any repair that looks easy,i had to do a little more than what i had originally anticpated.
i was hoping for an access panel to the igniter,but after removing the lower drawer,there was only the heat shields and pans,about 20 screws later i got
to the igniter and spliced it in place,then reassembled it without too m ... Read more uch fuss -now my 93 year old friend can bake her pecan pies for charity that is her favorite hobby-thanks