9117898511 Kenmore Range - Instructions

I removed the oven grates and removed 2 screws that held the bottom pan in the oven to get easy access to the burner and igniter. Remove 2 screws that held the burner in place. Removed wire nuts. Removing burner allowed easy access to fasteners holding ignitre in place. Confirmed that the igniter was bad by checking the continuity. Or ... Read more dered part later in the evening from parts select. Part was here 2nd morning after I ordered it. Installed, and checked to make sure igniter wasworking properely. When check confirmed igniter was working, replace oven components. Saved myself $100 or more by doing it myself rather than having a repairman out.

took the bottom plates off with philips screwdriver.(note) there are two plates..outter and inner..to get to the two screws on the igniter.Remove igniter(two nuts). Install new. Cut the wires from old(lower part of oven and rewire with porclain wire nuts.Very simple...Partselect was great too..very fast shipping. Will do buisness again.

We follow the advise of one of you other viewers. It was so easy. Our thanks for the info and the speeding delivery

I removed the oven burner while the igniter attached. put unit on my bench and changed the igniter and reinstalled the burner and reattached the wires to the supply terminals. Tested the unit and it lite up ok.

Took off the 2 bottom covers, saw the igniter did'nt glow, checked for voltage,yes.Ordered part. when had part,pulled out ignitor,respliced wires, and did in reverse order.

I took out the racks, unscrewed the bottom cover, removed the bottom drawer, cut the leads for the igniter, removed the bad one, had a little difficulty installing the new one, the screws were a little longer than the old ones, and were a little hard to get at, rewired the the leads, and put everything back, and started it up and it worke ... Read more d great!

followed peoples advices and all went very smooth. make sure to undo bracket from behind bottom drawer as it will make your life much easier.

I first checked the power by pushing oven button, I heard the relay make a sound " CLICK" ,I then knew it wasnt the power .I then removed the oven racks and then I removed the the two screws holding the pan in place. I hit the power button and noticed the ignitor did not glow as it should.I ordered the part and replaced it and had froze ... Read more n pizza 20 minutes later.

Basically followed the instructions that others had posted. Removed the bad oven igniter by removing the two screws securing it to the burner. Attached the new ignitor and then spliced the new wires into the old wires with the ceramic nuts that came with new igniter.

i removed the oven door and then the lower panel.the two screws holding the igniter were hard to access, so i removed the gas rail.this made the job much easier. the advice from other people on this website was very helpful and made the repair much easier.just remember to shutoff both the electric and gas supply.

Removed bottom tray of oven, removed ignighter, unplug two wires.

I removed the oven racks and the bottom cover. The bottom cover had 2 hand tight screws. Then I had to remove the silver sheet metal plate attached with 1 screw. Then I removed the 2 small screws that held the old Igniter in place. Then removed the 2 wire nuts connected to the oven wires. The new igniter fit in the same place as the ... Read more old and I attached it using the same old screws. Then I connected the wires using the new wire nuts provided in the igniter kit. After testing the new igniter by turning the oven on to 200F, i replaced all the parts i removed including the silver plate the oven bottom and the racks.

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my p ... Read more lan :)

1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy

I took the old igniter out and replaced it with a new one.