911726 Kenmore Range - Instructions

I removed the oven door, racks, and oven floor. That was easy, the floor had two thumb screws and one phillips/hex screw. I removed the lower drawer and the 2 covers above the drawer. The igniter was held in place by two phillips/hex screws. Had to manuver a bit to get the right angle to remove the screws. THE MOST IMPORTANT PART OF ... Read more THE REPAIR, when you cut the two wires to remove the old igniter, cut them off as close to the old igniter module as possible. On my stove one of the wires on the new igniter was about an inch too short and I had to add a section of wire. Overall the whole job was easy. Keep track of screws as you remove them.

Removed bottom tray of oven, removed ignighter, unplug two wires.

Took off the 2 bottom covers, saw the igniter did'nt glow, checked for voltage,yes.Ordered part. when had part,pulled out ignitor,respliced wires, and did in reverse order.

I first checked the power by pushing oven button, I heard the relay make a sound " CLICK" ,I then knew it wasnt the power .I then removed the oven racks and then I removed the the two screws holding the pan in place. I hit the power button and noticed the ignitor did not glow as it should.I ordered the part and replaced it and had froze ... Read more n pizza 20 minutes later.

We follow the advise of one of you other viewers. It was so easy. Our thanks for the info and the speeding delivery

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off

The stories posted on your web page are great - only improvement would to add a schematic of the parts being removed - no issues were encountered - great service by the way - part arrived the next day - a Saturday!

John M.

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, i ... Read more gniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?

simple remove & replace. 2 min job. Couldn't be happier.

I took the old igniter out and replaced it with a new one.

This site provides excellent instructions and saved a lot of time and effort.

Replacing the part only requires basic skills and attention to detail. The kit I received included ceramic wire nuts to splice the new igniter to the old connections. Be sure to leave enough wire to mke the connections properly.

replaced oven igniter - further details superflous as others have acurately documented the fix and procedure - thanks to all of you -

There are other descriptions here, but here's my story. I pulled the oven door off (pull straight up on it, it will come off) and removed the bottom warming drawer (there are plastic tabs on the outside of each side of the drawer--slide them and pull, several times on each side). I turned off the gas from behind the stove and unplugged th ... Read more e range, undid two screws at the back of the oven floor and lifted it forward and up. The burner is visible, but here is the hard part. The bolts holding the ignitor are underneath it and angled such that it is almost impossible to get any type of tool near them. I have small hands, and that helped. The screws are a bolt-head type or hex head, and I found that a one quarter inch open end wrench sort of fit. 6mm was too small and 7mm was too large. I managed to get the screws loosened after much struggling and manuvering, with half my body inside the oven, and once it was out, I was able to reach in from where the warming drawer was and unscrew the two wire leads attached from the ignitor to the power. They are held by plastic screwcaps. The reverse process was self explanatory, except that you should put the new ignitor in the oven and feed the wires down through the back panel, then attach the screwcaps to join the wires to the leads. Then go back in the oven and attach the ignitor, back screw first, and tighten it all the way, since you may not be able to reach it once the front screw is in. Also, use the screws that come with the new ignitor, since they are easier to start than the old ones. Tighten the screws as tight as you can get them so the ignitor doesn't wiggle, then turn the gas back on and plug it in, and test it before you put it back to gether. Mine worked, but it was a pain to do, kind of like working on an old car that wasn't designed to be fixed easily. Good luck.

Using the crescent wrench, I first removed the bolt holding the cover plate that separates the wiring from the broiler section of the oven.

Then I removed the wire nuts that connected the wires from the igniter to the wires from the oven.

Then I removed the two screws that attached the igniter to the oven.

... Read more >I then reversed the process, first attaching the igniter to the oven, then connecting the wires from the igniter to those from the oven using the wire nuts. Finally, I replaced the cover plate on the assembly.

The primary difficulty with the process was the small space to work in. One has to reach to the back of the broiler area to remove the bolt, screws and wire nuts. Some of these operations require two hands, and there's no room for both arms in this area.

However, that said, this is the third time we've replaced the igniter. It seems that it only lasts about 4 years before it needs to be replaced. It's not all that hard to do.