911606 Kenmore Range - Instructions

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cov ... Read more er off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

i went for 3 months waiting on the electrician who never came then asked the plumber who else could fix it and he said my husband could it only needed to unscrew 4 tiny screws and unplug and cut and twist wires back the hardest part was reaching the bolts hooked to the ignighter the burner was in the way and is not as easy to remove as so ... Read more meone has said all in all it saved us 100 dollars and could have saved us months of burning food trying to cook on broil if i had only called the plumber first.ha ha

Go to utube videos for this are there

I rempved the top and bottom doors, than the wire rackes followed by the bottom base of the oven. Then I removed the burner cover plate so I could get to the igniter.. I removed the cover plate for the wiring (2 wires), unpluged them, removed the igniter (2 screws). I had to cut the wires on the old igniter and couple the ends to the new ... Read more igniter and then replaced everything by just reversing all that I did. Simple! Easy!

- removed the oven unit from the wall
- removed the aluminum backplate to expose the wiring
- Removed both glass wire nuts and disconnected the heating element\
- From the front, I removed both retainer screws and pulled the element wires through.
- In reverse order I reinsalled the new wires and screwed on the heating ... Read more element.
-I reattached the electrical wiring and rear pane.
- I re-installed the unit into the wall.

Straight forward as per instructions. Removed old igniter, replaced and tested new one and it worked. However, the gas oven would not turn of. Valve may be defective. Knob control is not stripped and turned to full stop. Troubleshooting continues. Part(s) and instructions worked perfectly.

1. I have searched info on the internet and found that site.
2. Initially I could not figure out how to unscrew ingniter. After reading more post I have found out how to access nuts underneath.
3. After I have removed lower drawer and unscrewed metal cover and then inginter nuts.
4. I have got a part with two wires attached ... Read more to the igniter and two porcelan insulator, so it was very easy to cut old wires and connect with an igniter wires in parallel

/||\
||

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

First I disconnected power, then removed two screws from igniter & cliped two wires. Then installed new igniter & with the wire nuts supplied refastened to supply lines in oven.
PartSelect makes repairs quick & easy. It just takes a little smarts on your part.

It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas int ... Read more o the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.

well first off I repair commercial HVAC equipment for a major drug company so I think I've done it all.I thought it cant be much different than any burner assembly.I made it harder than it had to be,anyone can do this.I removed lots of unneccessary things.Let me help you only take out the drawer on bottom of stove.so I started on top and ... Read more worked my way down.save time and open the stove to were the door stops then have faith and give a good yank.this will remove the door,dont be afraid it will go right back on those two hinges easy.now that this is out of the way remove the bottom plate that covers the burner assembly (2 screws)in back pull it out then you see the igniter.as I said before with drawer pulled out remove the 2 1/4"nuts screws holding it up then from bottom.Unplug this stove then remove the 2 places its plugged in to.after you remove this there are 2 screws that hold it into the igniter remove them .cut the wires with enough room to re use the plug ends.strip the wires and use the wire nuts that they provide then put back together with new wires on new igniter then.re attach.put everything back together in the reverse order you took them apart.plug in stove and see the igniter light up again and light stove.do not call repairman you can do this.save your money for you its bad enough you have to buy anything else.

I frist remove the screws that hold the element in place disconnected two wires.That didn't take long.Call aronud my area for part.They wanted 90.00 plus taxs.Went on line to find it much cheaper came in the mail very fast and put it in my self.Very easy and saved money too.It took less then 3 mins to put in.If I could do it you can too.T ... Read more hank You,Bearice & Robert Reynolds P.S works great and no yelling at each other.Easy

Removed grills, oven bottom, heat deflector, and the two igniter mounting screws. Pulled out igniter, removed two wire twist caps and old igniter. Cut off ragged ends of wires coming from the stove side and re-stripped the wire ends. Attached oven side wires to new igniter wires using new twist caps. Reassembled everything in reverse ... Read more order. Tested oven operation to ensure that the gas ignited promptly. (It did).

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards toward ... Read more s the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.

Remove oven door,just open slighty and pull door up no tools.Take oven draw out.Remove oven floor held by two nuts in rear.You will now see the igniter,remove two screws holding it and the one screw holding the long tube at the front.The best tool I used was 1/4 drive socket set with a 6" ext.I did'nt need a new bracket that came with the ... Read more part and I cut the old igniter wires and wired in the new one because it had a special connectors.If your are a handy person,its EASY.