9114553 Kenmore Range - Instructions

I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!

The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!

All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy

Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached ... Read more the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.

Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to ... Read more swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.

My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.

.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.

1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two reta ... Read more ining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake

First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and recon ... Read more necting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.

Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven ... Read more . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.

Easy

I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. ... Read more I then secured the new unit to the oven wall with the two screws.

Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!

This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices ... Read more !
Thank you,

1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace o ... Read more f tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.