9114552191 Kenmore Range - Instructions

.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!

All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy

My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.

.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.

First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and recon ... Read more necting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.

Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven ... Read more . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.

I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. ... Read more I then secured the new unit to the oven wall with the two screws.

Easy

1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two reta ... Read more ining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake

1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace o ... Read more f tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.

Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!

This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices ... Read more !
Thank you,

Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)

After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new e ... Read more lement from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.

Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & sinc ... Read more e I was so tired from all of this 5-minute activity, I rested.

Al S.