91144003990 Kenmore Cooktop - Instructions

This was really easy, and pretty with no problems or issues It took me longer to write this than to do the actual installation. I used a digital camera to help me remember where things were, but a pen/paper works fine. Here's what I did:

1. Turn off the breaker for the cooktop.

2. Remove (2) 1/4" hex screws directly ... Read more under cooktop. You may need to open oven door to reveal them.

2. Prop up cooktop. I used the box the replacement element came in.

3. The element is held in place with (3) brackets held in by a #2 philips screw each. Mark the location of each of the brackets. There are numbers on the element to help you do this.

4. Write down where each of the wires connects to the element. There's only a few of them, but I tend to forget that stuff. The wires have female spade-type connectors that connect to the male ends on the element.

5. Using a needle-nose or small pliers wiggle each wire off the element. Grab the wires by the end of the female connector when you do this. I found it helpful to use a small flat screwdriver to help pry them off. Mine were on pretty tight, so expect this to take a few mins. If you have problems getting to the wires, remove the brackets (next step) first and come back to this one. I let the element hang from the wires without any problems, but I still wouldn't recommend it.

6. Remove each of the screws with a #2 philips screwdriver. Support the element with your hand and gently pull each bracket away from the element. Once they're all gone, the element should just come out. I took a look at my old element and saw that the large burner wires were melted in a couple places, so it was definitely broken.

7. If necessary, clean the underside of the cooktop surface with a clean papertowel. There was a little dust from the old element on mine.

8. Connect the new element and test to make sure it works by turning on the breaker and turning on the burner for a second or two. Note: This will make the top of the element hot for some time, so test it and go away for a few mins. If it works OK, proceed. If not, disconnect and figure out what else may be wrong.

9. Using the old element, make copies of the marks you made for the bracket locations onto the new element. You'll have to punch through the insulation when re-attaching the screws.

10. Re-wire the new element, if necessary and re-attach the brackets over the marks you made. This may be a pretty tight fit because the new element was thicker than the old on mine. I opened up the brackets a bit to make it not so hard to re-attach. Hook the brackets on and squeeze them over the element. The holes in the brackets need to line up with the holes drilled into the bottom of the element. If they don't, spin the element around (or detach and re-attach the brackets) till they do.

11. Screw in the (3) screws over the brackets pushing them through the insulation on the element.

12. Close the cooktop and reattach the hex screws under it (1/4" hex).

13. Turn on the breaker and test again.

Thats it, works great now. Good Luck

The outer ring on the adjustable large haliant surface burner of our smooth top stove would not work. It would only work on the small (inner) size.

Found the part on this site, ordered, 3 days later, and it was fixing time.

2 screws removed to lift cooktop, 2 screws to remove old burner and disconnected 4 electric ... Read more clips one at a time and placed them in same position on new burner. Replace the 4 screws and done.

VERY SIMPLE.

-Turn off breaker
-Undo the two screws that hold the top surface down
-Prop up top surface with a board
-Remove two screws/spring clips holding burner
-Transfer electrical plugs to new burner (this was the most challenging part)
-Screw new burner in place
-Lower surface
-Secure surface

First and foremost, I am a 63 year old cooky baking GRANDMOTHER. I don't know anything about fixing appliances. I read the other repair stories pertaining to my burner and I thought, "why not."
It was a snap!

My part arrived the very next day, bless you Parts Select! I just did what the others (see above) did: I remov ... Read more ed 2 screws to release the stove top, then I took a few digital photos to be sure I would know where the wires went. I released the old burner, pulled out the thingamajigs that held the wires in the old burner, then pushed the new ones in their place, replaced the stove top, plugged it back in, turned it on and jumped for joy! If I can do this, anyone can.

The burner would work but you could not regulate the heat. I ordered and replaced the control switch for that burner. The part was like for like and reasonably priced compared to other websites and dealer. The picture showed that it was identical. I ordered one day and it was here the next. I had drawn a diagram of where the wires went on ... Read more the old switch so it was very easy to replace. Probably took me 15 minutes or so. Works perfectly and by buying from this website it saved me a few bucks.

The hardest part was getting the correct part. I trusted the on line number and the first part I received was incorrect. I should have taken the part number off the old switch. When I did, I found out that the part number changed when I tried to order it. When the part came, the wiring instructions were not even close. I just took one wir ... Read more e at a time off the old switch and put it on the same terminal of the new switch. The repair was/is very simple made complex and too much time because of a wrong part and incorrect wiring instructions. As far as getting the incorrect and correct parts through the mail it was very fast. Received both parts in less than 3 days. A bonus is that I sent the old switch back for a rebate. Thanks for that.

Looked up the part, ordered it, and it was there in 3 days. It was slightly different than the old control, but a very well-written set of instuctions detailed which wires to move to which terminal. The entire repair took about 30 minutes, including moving the range out, replacing the control, and push the range back in place. Works pe ... Read more rfectly.

Removed range from cabinets then approximately 6 sheet metal screws from the front of the range and two 1/4" sheet metal screws from the side to remove the front and top of the range. Lifted the cook top removed the two screws from the rotary switch and followed the directions included with switch to connect the wires. In reverse order ... Read more reassembeled the range.
Quick & Easy

1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws

Read less