9114398611 Kenmore Cooktop - Instructions

I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.

First i shut off the power since this is an electric cook top/range. I then removed the knob and the two screws that hold the burner switch in place. I removed the wires one at a time and connected each to the new switch. I then reattached the screws to the switch. The most difficult part to me was breaking off the switch stem at the ... Read more right level. I got that done and finally selected the appropriate adapter for the stem/knob fit.

TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet ... Read more , but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.

lifted hood top unscrewed 4 small screws opening lid to switch housing took out 2 small screws that held the switch and then transfered wires to new switch replaced new switch with 2 new screws and back to working again walla! Time spent less than 30 minutes very simple as the instructions were very self explainatory.

I reviewed the schematic. Removed the outer casing. Pulled out the existing wires and replaced them exactly on the new switch. Snipped out off the control stem to match the others. There was a small metal piece on the old stem which holds on the knob. I removed it from the old stem and put it on the new stem and Eureka.

I ordered the wrong part to start with. (READ CAREFULLY!) I reordered the correct part and it was simple. I unpluged the old element, plugged in the new one replaced the drip pan and trim ring and we were back cooking.
Service was fast, lady I spoke with on the phone to exchange parts was knowegable and nice. Great people to deal wi ... Read more th.

I found the received switch (PS12070192) a poor replacement for the original, or even the earlier replaced part (PS11744446, in 2016) I was going to replace since the press/return feature seemed slow to return.

The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out ... Read more at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.

I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.

I have reinstalled the earlier unit.

Is part# PS 11744446 no longer available?



James E Weimholt. [email protected]

Lifted range top, disconnected and labled wires from old switch, removed old switch, replaced wires on new switch, installed new switch.
NOTE: Local appliance store informed me that the electric cooktop was too old and that a replacement switch was not available and wanted to sell me a new cooktop for $795!
I found the switch ... Read more on PartSelect and repaired the cooktop. Total cost... UNDER THIRTY DOLLARS!!

Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element ma ... Read more king sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.

Cut Wires to old terminal block and wired in new Terminal Block

I ordered a new drip pan. Piece of cake. Stove looks new again.

Installed easily, was most impressed with the speed of delivery and it was the perfect size!!

Ordered the part and set it in.

I unplugged the old unit and plugged in the new one! It works.

it was very easy, a few seconds and new range for a cuople of years more!