The drip bowl on your range is designed to catch any spills that may occur when cooking. This drip bowl is chrome in color and is 6 inches in diameter. The chrome drip bowl is intended for use with rolled, terminal-style plug-in surface element units. The drip bowl is located beneath the surface element, so you will need to remove the ele...Read morement prior to swapping out the old drip bowl for a new one. Many of our customers have rated this repair as easy, and you will not require any tools to complete it. This part is sold individually.
Drip bowls are located under the heating elements and catch grease and spills that come from cooking on your stove top. If your drip bowl is damaged or rusted, it could allow grease to drip inside your range. This 8 inch chrome drip bowl fits most electric ranges. Before you replace your damaged drip bowl, make sure the element is turned ...Read moreoff and cool to the touch. Installation is easy, just remove the element, replace the current drip bowl, and reattach the element. Make sure the small hole on the bowl lines up with the element socket. Drip bowls are sold separately.
The surface element or the coil surface element transfers heat to the area on top of the range. The element is 8 inches in diameter. If your surface element does not heat, overheats, or is inconsistent, replacing this part can be the solution. If you would like to determine whether the element is defective, use a multimeter. Before instal...Read moreling your new element, make sure that the drip bowl is properly aligned with the notch of the pan. Insert new element into the reciprocal at a 40 degree angle. Refer to the instructions provided by the manufacturer for more guidance.
This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface burner terminal block kit connects the wiring harness to the surface elements. It is important to shut off the power to the appliance befor...Read moree starting this repair. You will need to remove all four elements, trim rings, and drip bowls to access the terminal block on your stovetop. This is an OEM replacement part that is sourced from the genuine manufacturer.
This is an element disk but may also be known as a surface element and it is a part for your range. The function of this disk is to give heat to the cooking area on top of the range. This disk is for your seven-inch element, and is off-black in color. The most common reason for needing to replace this part is if your element is no longer ...Read moreheating, or is taking too long to heat. To make this repair you will need a screwdriver set, a nut driver, and a pair of needle-nose pliers.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
There was no heat on the coils.
48 of 52 peoplefound this instruction helpful.
Shaohui from East Lansing, MI
Easy
15 - 30 mins
Pliers
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Was this helpful?
Thank you for voting!
Large burner would operate on high setting only.
22 of 28 peoplefound this instruction helpful.
Ernest from Bellevue, NE
Really Easy
15 - 30 mins
Pliers, Socket set
1. Removed the back panel. 2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time. 3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range. 4. Replaced the burner knob and replaced the back panel.
Was this helpful?
Thank you for voting!
Surface burner coil did not work.
23 of 33 peoplefound this instruction helpful.
Gregory from Mont Belvieu, TX
Easy
30 - 60 mins
Nutdriver, Screw drivers, Socket set
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet
... Read more, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.